15 · Exemplos Raspberry Pi Pico SDK
Este capítulo é o equivalente para Raspberry Pi Pico de arduino-examples.md, micropython-examples.md, esp-idf-examples.md e stm32-hal-examples.md: os mesmos dez cenários, adaptados para C nativo com Pico SDK (pico-sdk 1.5+ / 2.x) e rede baseada em LwIP.
Estes exemplos falam com o rbAmp diretamente através da API bruta de registos I²C. Destinam-se a firmware embebido de produção no RP2040 / RP2350 — controlo direto do Cortex-M0+ / M33 de dois núcleos, integração com o cliente MQTT do LwIP, FATFS e as primitivas de suspensão / persistência do SDK.
Não é fornecida nenhuma biblioteca dedicada ao Pico SDK — as bibliotecas cliente cobrem Arduino (incl. arduino-pico para RP2040 através da API Wire), MicroPython (corre na porta RP2040), ESP-IDF e CPython em SBC Linux; veja a tabela de bibliotecas cliente no README. Para firmware nativo do Pico SDK em C, siga as receitas de API bruta abaixo. Se quiser uma API de nível mais alto no RP2040, o caminho mais fácil é o núcleo arduino-pico + a biblioteca Arduino do rbAmp.
Alvos suportados e cadeia de ferramentas
| Alvo | Validado | Wi-Fi | Notas |
|---|---|---|---|
| Raspberry Pi Pico (RP2040) | ✓ | não | Exemplos apenas I²C 1–3, 5, 7 |
| Raspberry Pi Pico W (RP2040 + CYW43) | ✓ | sim | Todos os exemplos; usa pico-cyw43-arch + LwIP |
| Raspberry Pi Pico 2 (RP2350) | ✓ | não | Cortex-M33 |
| Raspberry Pi Pico 2 W (RP2350 + CYW43) | ✓ | sim | Todos os exemplos |
Cadeia de ferramentas: pico-sdk 1.5.1+ (ou 2.x para RP2350), CMake 3.13+, arm-none-eabi-gcc 12+; recomenda-se a extensão oficial "Raspberry Pi Pico" para VS Code.
Estrutura do projeto
Todos os exemplos usam a estrutura de projeto padrão do pico-sdk:
example_NN/
├── CMakeLists.txt
├── pico_sdk_import.cmake
└── src/
├── example_NN.c
├── rbamp_io.h
├── rbamp_io.c
└── lwipopts.h (only for Wi-Fi examples)
CMakeLists.txt de topo:
cmake_minimum_required(VERSION 3.13)
# Pull in the SDK before project() — see pico-sdk template.
include(pico_sdk_import.cmake)
# For Pico W, set BOARD before project():
# set(PICO_BOARD pico_w)
project(example_NN C CXX ASM)
set(CMAKE_C_STANDARD 11)
pico_sdk_init()
add_executable(example_NN
src/example_NN.c
src/rbamp_io.c)
target_include_directories(example_NN PRIVATE src)
# Always-required libraries.
target_link_libraries(example_NN
pico_stdlib
hardware_i2c)
# Wi-Fi examples add CYW43 + LwIP + mqtt:
# target_link_libraries(example_NN
# pico_cyw43_arch_lwip_threadsafe_background
# pico_lwip_mqtt
# pico_lwip_sntp)
# target_compile_definitions(example_NN PRIVATE WIFI_SSID=\"...\" WIFI_PASSWORD=\"...\")
# Route stdio to USB CDC (for Pico's serial console).
pico_enable_stdio_usb(example_NN 1)
pico_enable_stdio_uart(example_NN 0)
pico_add_extra_outputs(example_NN)
Compilar e gravar:
mkdir build && cd build
cmake ..
make -j
# Drag-and-drop the .uf2 onto the RPI-RP2 / RP2350 USB mass-storage device.
Índice dos exemplos
| # | Título | Dificuldade | Saída | MQTT | DRDY | Multi-módulo | Bidirecional | Caso de utilização |
|---|---|---|---|---|---|---|---|---|
| 1 | Leitura rápida | mínimo | USB stdio | — | — | — | — | Teste de funcionamento |
| 2 | Contador de energia de 60 segundos no OLED | baixo | SSD1306 | — | — | — | — | Contador Wh em caixa |
| 3 | Monitor multi-módulo | baixo | USB stdio | — | — | sim (3) | — | Monitorização de toda a casa |
| 4 | Medidor de energia por aparelho (UI3) | médio | — | sim | — | — | — | Sub-medição no HA |
| 5 | Bidirecional no mestre num módulo BASIC | médio | USB stdio | — | sim | — | sim (mestre) | Casa solar em nível BASIC |
| 6 | Balanço energético doméstico | alta | — | sim | — | sim (3) | sim | Balanço energético doméstico completo |
| 7 | Deteção de eventos de energia | médio | USB + SD | — | sim | — | — | Registo de eventos de eletrodomésticos |
| 8 | Publicador MQTT com auto-discovery do HA | médio | — | sim (+disco) | — | — | opcional | Integração HA pronta a usar |
| 9 | Registador com bateria e sono dormente | médio | — | sim | — | — | — | Medidor para exterior / fora da rede |
| 10 | Tarifa de tempo de uso (TOU) com relógio de parede SNTP | médio | USB stdio | sim | — | — | opcional | Medição de tarifa de ponta / fora de ponta |
Os exemplos Wi-Fi (4, 6, 8, 9, 10) exigem Pico W ou Pico 2 W.
Auxiliares comuns (rbamp_io.h / rbamp_io.c)
Coloque estes ficheiros no diretório src/ do seu projeto. Para poupar espaço, a linha #include "rbamp_io.h" é omitida em cada exemplo abaixo.
rbamp_io.h
/**
* @file rbamp_io.h
* @brief Raw I2C helpers for the rbAmp slave (Raspberry Pi Pico SDK).
*/
#pragma once
#include
#include
#include "pico/stdlib.h"
#include "hardware/i2c.h"
#ifdef __cplusplus
extern "C" {
#endif
#define RBAMP_I2C_TIMEOUT_US 50000U /* 50 ms */
/**
* @brief Initialise the I2C peripheral and pin functions.
* @param i2c_inst i2c0 or i2c1.
* @param sda_gpio SDA GPIO number (e.g. 4 for default i2c0).
* @param scl_gpio SCL GPIO number (e.g. 5 for default i2c0).
* @param baudrate Bus speed (use 50000 — the recommended 50 kHz; wrap reads in a short retry, see ch. 11 §2.2).
*/
void rbamp_io_init(i2c_inst_t *i2c_inst, uint sda_gpio, uint scl_gpio,
uint baudrate);
/**
* @brief Read one byte from a register of an rbAmp slave.
* @return PICO_OK on success, an error code otherwise.
*/
int rbamp_io_read_u8(uint8_t addr, uint8_t reg, uint8_t *out);
/**
* @brief Read a little-endian float32 from four consecutive registers.
* @details Reads four consecutive bytes. rbAmp supports READ auto-increment
* (a single burst-read is valid for atomicity). The per-byte form
* is shown for clarity. See chapter 11 for asymmetry rules.
*/
int rbamp_io_read_float_le(uint8_t addr, uint8_t reg, float *out);
/**
* @brief Read a little-endian uint32 from four consecutive registers.
*/
int rbamp_io_read_u32_le(uint8_t addr, uint8_t reg, uint32_t *out);
/**
* @brief Write a single byte to a register.
*/
int rbamp_io_write_u8(uint8_t addr, uint8_t reg, uint8_t val);
/**
* @brief Broadcast CMD_LATCH_PERIOD to every rbAmp with GC reception
* enabled (FLEET_CONFIG.bit0 = 1; opt-in, default OFF).
* @details Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi.
* Slaves reject any first byte != 0xA5. See chapter 11 §6.3.2.
* @param tick16 Caller's 16-bit window counter (mirrored at GC_TICK 0x59).
* @param group GROUP_ID filter (0 = all-call).
* @return PICO_OK on ACK; PICO_ERROR_GENERIC on NACK — fall back to per-module.
*/
int rbamp_io_broadcast_latch(uint16_t tick16, uint8_t group);
/**
* @brief Probe whether a slave responds at the given address.
* @return true if the slave acks, false otherwise.
*/
bool rbamp_io_probe(uint8_t addr);
/**
* @brief Block until DATA_VALID bit 0 of register 0xCE reads 1, or timeout.
* @return PICO_OK on success, PICO_ERROR_TIMEOUT otherwise.
*/
int rbamp_io_wait_ready(uint8_t addr, uint32_t timeout_ms);
/* ===== rbAmp register addresses (subset used in examples) ===== */
#define RB_REG_STATUS 0x00U
#define RB_REG_COMMAND 0x01U
#define RB_REG_VERSION 0x03U
#define RB_REG_AC_FREQ 0x20U
#define RB_REG_PERIOD_VALID 0x07U
#define RB_REG_U_RMS 0x86U
#define RB_REG_I0_RMS 0x8EU
#define RB_REG_I1_RMS 0x92U
#define RB_REG_I2_RMS 0x96U
#define RB_REG_P0_REAL 0xA6U
#define RB_REG_PF0 0xB2U
#define RB_REG_Q0 0xD0U
#define RB_REG_DATA_VALID 0xCEU
#define RB_REG_PERIOD_AVG_P0 0xDCU
#define RB_REG_PERIOD_AVG_P1 0xC2U
#define RB_REG_PERIOD_AVG_P2 0xC6U
#define RB_REG_PERIOD_MAX_P 0xE0U
#define RB_REG_PERIOD_LATCH_MS 0xECU
/* ===== Commands ===== */
#define RB_CMD_RESET 0x01U
#define RB_CMD_LATCH_PERIOD 0x27U
#ifdef __cplusplus
}
#endif
rbamp_io.c
#include "rbamp_io.h"
#include
#include "pico/error.h"
static i2c_inst_t *s_i2c = NULL;
void rbamp_io_init(i2c_inst_t *i2c_inst, uint sda_gpio, uint scl_gpio,
uint baudrate) {
s_i2c = i2c_inst;
i2c_init(s_i2c, baudrate);
gpio_set_function(sda_gpio, GPIO_FUNC_I2C);
gpio_set_function(scl_gpio, GPIO_FUNC_I2C);
/* The rbAmp board carries its own pull-ups; do NOT enable the internal
* pulls unless yours are physically removed. */
}
/**
* @brief Internal helper — one register read.
* @details Pattern: write reg-address (nostop=true) + read 1 byte.
*/
static int read_one(uint8_t addr, uint8_t reg, uint8_t *out) {
int n = i2c_write_timeout_us(s_i2c, addr, ®, 1,
/*nostop=*/true, RBAMP_I2C_TIMEOUT_US);
if (n != 1) return PICO_ERROR_GENERIC;
n = i2c_read_timeout_us(s_i2c, addr, out, 1,
/*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
return (n == 1) ? PICO_OK : PICO_ERROR_GENERIC;
}
int rbamp_io_read_u8(uint8_t addr, uint8_t reg, uint8_t *out) {
return read_one(addr, reg, out);
}
int rbamp_io_read_float_le(uint8_t addr, uint8_t reg, float *out) {
uint8_t buf[4];
for (int i = 0; i < 4; i++) {
int rc = read_one(addr, (uint8_t)(reg + i), &buf[i]);
if (rc != PICO_OK) return rc;
}
memcpy(out, buf, sizeof(float)); /* RP2040 / RP2350 are little-endian */
return PICO_OK;
}
int rbamp_io_read_u32_le(uint8_t addr, uint8_t reg, uint32_t *out) {
uint8_t buf[4];
for (int i = 0; i < 4; i++) {
int rc = read_one(addr, (uint8_t)(reg + i), &buf[i]);
if (rc != PICO_OK) return rc;
}
*out = (uint32_t)buf[0] | (uint32_t)buf[1] << 8
| (uint32_t)buf[2] << 16 | (uint32_t)buf[3] << 24;
return PICO_OK;
}
int rbamp_io_write_u8(uint8_t addr, uint8_t reg, uint8_t val) {
uint8_t tx[2] = { reg, val };
int n = i2c_write_timeout_us(s_i2c, addr, tx, 2,
/*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
return (n == 2) ? PICO_OK : PICO_ERROR_GENERIC;
}
int rbamp_io_broadcast_latch(uint16_t tick16, uint8_t group) {
/* Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi. */
uint8_t tx[5] = {
0xA5, /* frame magic */
RB_CMD_LATCH_PERIOD, /* opcode 0x27 */
group, /* group_id (0 = all-call) */
(uint8_t)(tick16 & 0xFF),
(uint8_t)((tick16 >> 8) & 0xFF),
};
int n = i2c_write_timeout_us(s_i2c, /*addr=*/0x00U, tx, sizeof tx,
/*nostop=*/false, RBAMP_I2C_TIMEOUT_US);
return (n == (int)sizeof tx) ? PICO_OK : PICO_ERROR_GENERIC;
}
bool rbamp_io_probe(uint8_t addr) {
uint8_t dummy;
/* A 1-byte read is the simplest ACK probe — read the STATUS register. */
return read_one(addr, RB_REG_STATUS, &dummy) == PICO_OK;
}
int rbamp_io_wait_ready(uint8_t addr, uint32_t timeout_ms) {
absolute_time_t deadline = make_timeout_time_ms(timeout_ms);
while (!time_reached(deadline)) {
uint8_t v = 0;
if (rbamp_io_read_u8(addr, RB_REG_DATA_VALID, &v) == PICO_OK
&& (v & 0x01U)) {
return PICO_OK;
}
sleep_ms(50);
}
return PICO_ERROR_TIMEOUT;
}
Exemplo 1 — Leitura rápida (mínima)
Objetivo: imprimir U, I, P, PF por USB CDC uma vez por segundo. Hardware: Raspberry Pi Pico + um rbAmp UI1. I²C no GPIO 4 (SDA) / GPIO 5 (SCL) — pinos i2c0 por defeito.
src/example_01.c:
#include
#include "pico/stdlib.h"
#include "hardware/i2c.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
int main(void) {
stdio_init_all(); /* USB CDC stdio */
sleep_ms(2000); /* let the USB host enumerate */
/* I2C0 on GPIO 4 / 5 at the recommended 50 kHz. */
rbamp_io_init(i2c0, 4, 5, 50000);
/* Wait until the first RT window has been computed. */
if (rbamp_io_wait_ready(RB_ADDR, 2000) != PICO_OK) {
printf("ERROR: rbAmp not ready\n");
while (1) tight_loop_contents();
}
uint8_t ver = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_VERSION, &ver);
printf("rbAmp version: 0x%02X\n", ver);
while (true) {
float u, i_, p, pf;
rbamp_io_read_float_le(RB_ADDR, RB_REG_U_RMS, &u );
rbamp_io_read_float_le(RB_ADDR, RB_REG_I0_RMS, &i_);
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p );
rbamp_io_read_float_le(RB_ADDR, RB_REG_PF0, &pf);
printf("U=%.1fV I=%.3fA P=%+.1fW PF=%+.3f\n", u, i_, p, pf);
sleep_ms(1000);
}
}
Saída esperada na consola série:
rbAmp version: 0x04
U=230.1V I=0.262A P=+60.2W PF=+0.998
U=229.9V I=0.262A P=+60.1W PF=+0.998
...
Ligue à consola série com minicom -D /dev/ttyACM0 -b 115200 (Linux), screen /dev/cu.usbmodem* (macOS) ou PuTTY (Windows).
Exemplo 2 — medidor de energia de 60 segundos no OLED
Objetivo: contador Wh atualizado uma vez por minuto, mostrado num SSD1306 de 128×64 que partilha o barramento I²C do rbAmp. Hardware: Pico + rbAmp + SSD1306 (0x3C) no mesmo barramento. Biblioteca: um driver SSD1306 comum do Pico-SDK (p. ex. daschr/pico-ssd1306). A API do OLED abaixo é simbólica — substitua pelas chamadas do seu driver.
#include
#include
#include "pico/stdlib.h"
#include "rbamp_io.h"
#include "ssd1306.h"
#define RB_ADDR 0x50U
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
/* OLED shares the same i2c0. */
ssd1306_t oled;
ssd1306_init(&oled, 128, 64, 0x3C, i2c0);
rbamp_io_wait_ready(RB_ADDR, 2000);
/* Primer snapshot — discard its snapshot. */
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
double total_wh = 0.0;
while (true) {
sleep_ms(60 * 1000);
/* 1) Final snapshot. */
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50); /* let firmware finalise snapshot */
/* 2) Check PERIOD_VALID. */
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
printf("WARN: stale snapshot\n");
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
/* 3) Read time-averaged P. */
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
/* 4) Energy uses the MASTER clock. */
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
double e_wh = (double)avg_p * dt_s / 3600.0;
total_wh += e_wh;
t_prev_ms = t_now_ms;
/* 5) Render. */
char line[32];
ssd1306_clear(&oled);
snprintf(line, sizeof(line), "P: %6.1f W", avg_p);
ssd1306_draw_string(&oled, 0, 0, 1, line);
snprintf(line, sizeof(line), "dt: %6.1f s", dt_s);
ssd1306_draw_string(&oled, 0, 16, 1, line);
snprintf(line, sizeof(line), "%.2f Wh", total_wh);
ssd1306_draw_string(&oled, 0, 32, 2, line);
ssd1306_show(&oled);
printf("avg_P=%.1f E_period=%.3f total=%.3f\n", avg_p, e_wh, total_wh);
}
}
O driver OLED e o rbAmp partilham o i2c0 — nunca chame i2c_init() duas vezes; o rbamp_io_init() do auxiliar já o fez.
Exemplo 3 — Monitor multi-módulo
Objetivo: consultar três módulos (alimentação principal, esquentador, AC) e imprimir o total. Hardware: Pico + 3 × rbAmp UI1 em 0x50, 0x51, 0x52.
#include
#include
#include "pico/stdlib.h"
#include "rbamp_io.h"
typedef struct {
uint8_t addr;
const char *label;
} module_t;
static const module_t modules[] = {
{ 0x50, "Mains " },
{ 0x51, "Boiler" },
{ 0x52, "AC " },
};
#define N_MODULES (sizeof(modules) / sizeof(modules[0]))
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
/* Probe every module before entering the read loop. */
for (size_t i = 0; i < N_MODULES; i++) {
if (!rbamp_io_probe(modules[i].addr)) {
printf("ERROR: %s at 0x%02X not found\n",
modules[i].label, modules[i].addr);
while (1) tight_loop_contents();
}
}
printf("All modules OK\n");
while (true) {
float total_p = 0.0f;
printf("---\n");
/* Round-robin read. */
for (size_t i = 0; i < N_MODULES; i++) {
float u = 0.0f, p = 0.0f;
rbamp_io_read_float_le(modules[i].addr, RB_REG_U_RMS, &u);
rbamp_io_read_float_le(modules[i].addr, RB_REG_P0_REAL, &p);
printf("[%s] U=%.1f P=%+.1f W\n", modules[i].label, u, p);
total_p += p;
}
printf("TOTAL: %.1f W\n", total_p);
sleep_ms(2000);
}
}
Exemplo 4 — medidor de energia por aparelho (UI3)
Objetivo: um módulo UI3 com três pinças de corrente em três cargas diferentes na mesma fase; contadores Wh independentes publicados em MQTT a cada minuto. Hardware: Pico W (ou Pico 2 W) + 1 × rbAmp UI3 + rede Wi-Fi com um broker MQTT. Componentes do SDK: pico_cyw43_arch_lwip_threadsafe_background, pico_lwip_mqtt.
Acréscimos ao CMakeLists.txt:
set(PICO_BOARD pico_w)
target_link_libraries(example_04
pico_stdlib
hardware_i2c
pico_cyw43_arch_lwip_threadsafe_background
pico_lwip_mqtt)
target_compile_definitions(example_04 PRIVATE
WIFI_SSID=\"ssid\"
WIFI_PASSWORD=\"password\"
MQTT_BROKER_IP=\"192.168.1.10\")
src/lwipopts.h (mínimo — estenda a partir de pico-examples/pico_w/wifi/lwipopts_examples_common.h):
#pragma once
#include "lwip/apps/mqtt.h"
#define LWIP_MQTT 1
#define MEMP_NUM_SYS_TIMEOUT 8
/* Use the SDK's standard threadsafe-background opts. */
src/example_04.c:
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "lwip/dns.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
static const char *CH_NAMES[3] = { "main", "heatpump", "lights" };
static mqtt_client_t *s_mqtt;
static ip_addr_t s_broker_ip;
/**
* @brief MQTT connection-status callback (logs result; could trigger retry).
*/
static void mqtt_conn_cb(mqtt_client_t *client, void *arg,
mqtt_connection_status_t status) {
printf("MQTT connect status=%d\n", (int)status);
}
/**
* @brief Bring up Wi-Fi (CYW43) and connect to the MQTT broker.
*/
static void net_init(void) {
if (cyw43_arch_init()) {
printf("CYW43 init failed\n");
return;
}
cyw43_arch_enable_sta_mode();
if (cyw43_arch_wifi_connect_timeout_ms(WIFI_SSID, WIFI_PASSWORD,
CYW43_AUTH_WPA2_AES_PSK, 30000)) {
printf("Wi-Fi connect failed\n");
return;
}
printf("Wi-Fi up\n");
ipaddr_aton(MQTT_BROKER_IP, &s_broker_ip);
s_mqtt = mqtt_client_new();
struct mqtt_connect_client_info_t ci = { .client_id = "rbamp-ui3" };
mqtt_client_connect(s_mqtt, &s_broker_ip, 1883, mqtt_conn_cb, NULL, &ci);
}
/**
* @brief Publish one channel's state to MQTT.
*/
static void mqtt_publish_channel(const char *ch_name, float avg_p, double e_wh) {
char topic[64], payload[64];
snprintf(topic, sizeof(topic), "rbamp/%s/state", ch_name);
int n = snprintf(payload, sizeof(payload),
"{\"power\":%.1f,\"energy\":%.4f}", avg_p, e_wh);
mqtt_publish(s_mqtt, topic, payload, n, /*qos*/ 0, /*retain*/ 0,
NULL, NULL);
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD); /* primer */
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
double total_wh[3] = { 0.0, 0.0, 0.0 };
while (true) {
sleep_ms(60 * 1000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
/* PERIOD_AVG_P_W per channel: I0 at 0xDC, I1 at 0xC2, I2 at 0xC6. */
float avg_p[3];
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p[0]);
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P1, &avg_p[1]);
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P2, &avg_p[2]);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
t_prev_ms = t_now_ms;
for (int ch = 0; ch < 3; ch++) {
double e = (double)avg_p[ch] * dt_s / 3600.0;
total_wh[ch] += e;
printf("[%s] avg_P=%+.1f W E_total=%.3f Wh\n",
CH_NAMES[ch], avg_p[ch], total_wh[ch]);
mqtt_publish_channel(CH_NAMES[ch], avg_p[ch], total_wh[ch]);
}
}
}
Exemplo 5 — bidirecional no mestre num módulo BASIC
Objetivo: implementar contabilização bidirecional no mestre enquanto o módulo tem firmware BASIC. O Pico reage à descida do DRDY através de uma IRQ de GPIO e separa consumo / exportação. Hardware: Pico + rbAmp UI1; DRDY ligado ao GPIO 15.
#include
#include
#include "pico/stdlib.h"
#include "pico/critical_section.h"
#include "hardware/gpio.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define PIN_DRDY 15
static volatile bool g_data_ready = false;
/**
* @brief Shared GPIO IRQ callback for the Pico SDK.
* @details The SDK uses a single callback for all GPIO IRQs — we filter by pin.
* Keep the callback short (no I2C, no printf inside an IRQ).
*/
static void gpio_callback(uint gpio, uint32_t events) {
if (gpio == PIN_DRDY && (events & GPIO_IRQ_EDGE_FALL)) {
g_data_ready = true;
}
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
/* DRDY input with internal pull-up; falling-edge IRQ. */
gpio_init(PIN_DRDY);
gpio_set_dir(PIN_DRDY, GPIO_IN);
gpio_pull_up(PIN_DRDY);
gpio_set_irq_enabled_with_callback(PIN_DRDY, GPIO_IRQ_EDGE_FALL,
true, &gpio_callback);
double e_consumed_wh = 0.0;
double e_exported_wh = 0.0;
// Use uint64_t for microsecond counters — to_us_since_boot() returns u64;
// truncating to u32 overflows every ~71.6 minutes and produces a multi-kWh
// dt_s spike on the wrap.
uint64_t t_last_us = to_us_since_boot(get_absolute_time());
uint64_t t_last_print_us = t_last_us;
printf("Bidirectional accumulator started\n");
while (true) {
if (!g_data_ready) {
tight_loop_contents();
continue;
}
g_data_ready = false;
uint32_t t_now_us = to_us_since_boot(get_absolute_time());
/* Signed instantaneous P_real: + consume, − export. */
float p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p);
float dt_s = (float)(t_now_us - t_last_us) / 1000000.0f;
t_last_us = t_now_us;
if (p > 0.0f) e_consumed_wh += (double)p * dt_s / 3600.0;
else e_exported_wh += (double)(-p) * dt_s / 3600.0;
/* Summary print every 5 s — not on every RT window. */
if (t_now_us - t_last_print_us >= 5000000UL) {
t_last_print_us = t_now_us;
printf("P=%+8.1fW consumed=%.4f Wh exported=%.4f Wh net=%+.4f Wh\n",
p, e_consumed_wh, e_exported_wh,
e_consumed_wh - e_exported_wh);
}
}
}
Notes:
- O
gpio_set_irq_enabled_with_callback()do Pico SDK regista um callback partilhado para todas as IRQs GPIO; as chamadas posteriores agpio_set_irq_enabled()reutilizam-no. volatile boolbasta para a sincronização por um único sinalizador — o RP2040 é de emissão única e o booleano é lido de forma atómica.
Exemplo 6 — balanço energético doméstico
Objetivo: painel completo de balanço energético. Três módulos:
- rbAmp #1 na alimentação principal (STD — bidirecional)
- rbAmp n.º 2 na saída do inversor solar (BASIC OK)
- rbAmp #3 UI3 em três grandes cargas (bomba de calor HP, AC, VE)
O mestre usa rbamp_io_broadcast_latch() para instantâneos síncronos e publica um saldo retido em MQTT a cada minuto.
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"
#define ADDR_MAINS 0x50U
#define ADDR_SOLAR 0x51U
#define ADDR_LOADS 0x52U
#define REG_PERIOD_AVG_P_NEG_MAINS 0xFFU /* set per SKU datasheet on STD */
extern void net_init(void); /* same boilerplate as Ex. 4 */
extern mqtt_client_t *s_mqtt;
typedef struct {
double mains_in_wh;
double mains_out_wh;
double solar_total_wh;
double loads_wh[3];
} totals_t;
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(ADDR_MAINS, 2000);
rbamp_io_wait_ready(ADDR_SOLAR, 2000);
rbamp_io_wait_ready(ADDR_LOADS, 2000);
/* Primer snapshot on all modules (general call). GC is opt-in
* (FLEET_CONFIG.bit0, default OFF) — fall back to per-module on NACK. */
uint16_t gc_tick = 0;
if (rbamp_io_broadcast_latch(gc_tick++, 0) != PICO_OK) {
rbamp_io_write_u8(ADDR_MAINS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_SOLAR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_LOADS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
}
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
totals_t totals = {0};
printf("Home balance started\n");
while (true) {
sleep_ms(60 * 1000);
/* Synchronous snapshot on all modules. */
if (rbamp_io_broadcast_latch(gc_tick++, 0) != PICO_OK) {
rbamp_io_write_u8(ADDR_MAINS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_SOLAR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
rbamp_io_write_u8(ADDR_LOADS, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
}
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
t_prev_ms = t_now_ms;
/* ----- MAINS (bidirectional, STD) ----- */
uint8_t valid;
if (rbamp_io_read_u8(ADDR_MAINS, RB_REG_PERIOD_VALID, &valid) == PICO_OK
&& (valid & 0x01U)) {
float p_consume = 0.0f, p_export = 0.0f;
rbamp_io_read_float_le(ADDR_MAINS, RB_REG_PERIOD_AVG_P0, &p_consume);
if (REG_PERIOD_AVG_P_NEG_MAINS != 0xFFU) {
rbamp_io_read_float_le(ADDR_MAINS, REG_PERIOD_AVG_P_NEG_MAINS,
&p_export);
}
totals.mains_in_wh += (double)p_consume * dt_s / 3600.0;
totals.mains_out_wh += (double)p_export * dt_s / 3600.0;
}
/* ----- SOLAR (generation only) ----- */
if (rbamp_io_read_u8(ADDR_SOLAR, RB_REG_PERIOD_VALID, &valid) == PICO_OK
&& (valid & 0x01U)) {
float p = 0.0f;
rbamp_io_read_float_le(ADDR_SOLAR, RB_REG_PERIOD_AVG_P0, &p);
totals.solar_total_wh += (double)p * dt_s / 3600.0;
}
/* ----- LOADS (UI3, three channels) ----- */
if (rbamp_io_read_u8(ADDR_LOADS, RB_REG_PERIOD_VALID, &valid) == PICO_OK
&& (valid & 0x01U)) {
float p[3] = {0};
rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P0, &p[0]); /* I0 */
rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P1, &p[1]); /* I1 */
rbamp_io_read_float_le(ADDR_LOADS, RB_REG_PERIOD_AVG_P2, &p[2]); /* I2 */
for (int i = 0; i < 3; i++) {
totals.loads_wh[i] += (double)p[i] * dt_s / 3600.0;
}
}
double total_consumed = totals.mains_in_wh + totals.solar_total_wh
- totals.mains_out_wh;
double solar_self_used = totals.solar_total_wh - totals.mains_out_wh;
if (solar_self_used < 0.0) solar_self_used = 0.0;
printf("MAINS in=%.2f out=%.2f\n", totals.mains_in_wh, totals.mains_out_wh);
printf("SOLAR gen=%.2f self-used=%.2f exported=%.2f\n",
totals.solar_total_wh, solar_self_used, totals.mains_out_wh);
printf("LOADS HP=%.2f AC=%.2f EV=%.2f\n",
totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
printf("TOTAL household consumed=%.2f Wh\n", total_consumed);
char payload[512];
int n = snprintf(payload, sizeof(payload),
"{\"mains_in\":%.3f,\"mains_out\":%.3f,\"solar\":%.3f,"
"\"self_used\":%.3f,\"total_consumed\":%.3f,"
"\"hp\":%.3f,\"ac\":%.3f,\"ev\":%.3f}",
totals.mains_in_wh, totals.mains_out_wh, totals.solar_total_wh,
solar_self_used, total_consumed,
totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
mqtt_publish(s_mqtt, "home/energy/balance", payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
}
}
Exemplo 7 — deteção de eventos de energia
Objetivo: em cada flanco de DRDY, comparar P instantânea com uma EMA e registar os desvios significativos num cartão SD montado por SPI + FATFS. Hardware: Pico + rbAmp + módulo de cartão SD por SPI. Biblioteca: no-OS-FatFS-SD-SPI-RPi-Pico ou um port FATFS semelhante compatível com o SDK.
#include
#include
#include
#include "pico/stdlib.h"
#include "hardware/gpio.h"
#include "ff.h" /* FATFS API */
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define PIN_DRDY 15
#define EMA_ALPHA 0.05f
#define EVENT_THRESHOLD_W 200.0f
static volatile bool g_data_ready = false;
static FATFS s_fs;
static FIL s_logfile;
static void gpio_callback(uint gpio, uint32_t events) {
if (gpio == PIN_DRDY && (events & GPIO_IRQ_EDGE_FALL)) {
g_data_ready = true;
}
}
/**
* @brief Mount the SD card and open events.log in append mode.
*/
static bool sd_setup(void) {
if (f_mount(&s_fs, "", 1) != FR_OK) return false;
if (f_open(&s_logfile, "events.log",
FA_OPEN_APPEND | FA_WRITE) != FR_OK) return false;
return true;
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
if (sd_setup()) printf("SD mounted; logging to events.log\n");
else printf("WARN: SD card not available\n");
gpio_init(PIN_DRDY);
gpio_set_dir(PIN_DRDY, GPIO_IN);
gpio_pull_up(PIN_DRDY);
gpio_set_irq_enabled_with_callback(PIN_DRDY, GPIO_IRQ_EDGE_FALL,
true, &gpio_callback);
/* Seed the EMA with current power so we do not log a spurious startup event. */
float p_ema = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p_ema);
printf("Event detector started\n");
while (true) {
if (!g_data_ready) { tight_loop_contents(); continue; }
g_data_ready = false;
float p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_P0_REAL, &p);
float delta = p - p_ema;
p_ema = (1.0f - EMA_ALPHA) * p_ema + EMA_ALPHA * p;
if (fabsf(delta) > EVENT_THRESHOLD_W) {
const char *type = (delta > 0.0f) ? "TURN_ON" : "TURN_OFF";
char line[128];
int n = snprintf(line, sizeof(line),
"%lu %s delta=%+.1f W P=%.1f W EMA=%.1f W\n",
(unsigned long)to_ms_since_boot(get_absolute_time()),
type, delta, p, p_ema);
printf("%s", line);
UINT bw;
f_write(&s_logfile, line, n, &bw);
f_sync(&s_logfile); /* flush to the card */
}
}
}
Exemplo 8 — Publicador MQTT com descoberta automática do Home Assistant [Auto-discovery]
Objetivo: uma integração HA imediata. O Pico W liga-se ao Wi-Fi e a um broker MQTT, publica as configurações de Auto-discovery do HA (retidas) e emite um estado JSON a cada minuto. Hardware: Pico W (ou Pico 2 W) + um rbAmp UI1 + Wi-Fi + broker MQTT.
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define DEVICE_ID "rbamp_main"
#define DEVICE_NAME "Mains rbAmp"
extern void net_init(void); /* Wi-Fi + MQTT bring-up (Ex. 4) */
extern mqtt_client_t *s_mqtt;
/**
* @brief Publish one HA discovery config (retained).
*/
static void publish_discovery_sensor(const char *key, const char *friendly,
const char *unit, const char *dev_class,
const char *state_class) {
char topic[128], payload[512];
snprintf(topic, sizeof(topic),
"homeassistant/sensor/%s/%s/config", DEVICE_ID, key);
int n = snprintf(payload, sizeof(payload),
"{"
"\"name\":\"%s %s\","
"\"unique_id\":\"%s_%s\","
"\"state_topic\":\"rbamp/%s/state\","
"\"value_template\":\"{{ value_json.%s }}\","
"\"state_class\":\"%s\","
"\"device\":{"
"\"identifiers\":[\"%s\"],"
"\"name\":\"%s\","
"\"manufacturer\":\"rbAmp\","
"\"model\":\"rbAmp UI*\""
"}",
DEVICE_NAME, friendly, DEVICE_ID, key,
DEVICE_ID, key, state_class,
DEVICE_ID, DEVICE_NAME);
if (unit) n += snprintf(payload + n, sizeof(payload) - n,
",\"unit_of_measurement\":\"%s\"", unit);
if (dev_class) n += snprintf(payload + n, sizeof(payload) - n,
",\"device_class\":\"%s\"", dev_class);
n += snprintf(payload + n, sizeof(payload) - n, "}");
mqtt_publish(s_mqtt, topic, payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
}
/**
* @brief Publish the full set of HA discovery configs for one rbAmp.
*/
static void publish_discovery_all(void) {
publish_discovery_sensor("voltage", "Voltage", "V", "voltage", "measurement");
publish_discovery_sensor("current", "Current", "A", "current", "measurement");
publish_discovery_sensor("power", "Power", "W", "power", "measurement");
publish_discovery_sensor("energy", "Energy", "Wh", "energy", "total_increasing");
publish_discovery_sensor("frequency", "Frequency", "Hz", "frequency", "measurement");
publish_discovery_sensor("power_factor", "Power Factor", NULL, "power_factor", "measurement");
publish_discovery_sensor("apparent_power", "Apparent Power", "VA", "apparent_power", "measurement");
publish_discovery_sensor("reactive_power", "Reactive Power", "var", "reactive_power", "measurement");
}
/* Set to true by Ex.4's mqtt_conn_cb on MQTT_CONNECT_ACCEPTED.
* (Add `extern volatile bool s_mqtt_connected;` to the net_init translation unit.) */
extern volatile bool s_mqtt_connected;
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
/* MQTT connect is asynchronous — publishing discovery before the CONNECT
* callback fires causes mqtt_publish() to return ERR_CONN and the configs
* to silently disappear. Wait (bounded) for the connection. */
uint32_t mqtt_deadline = to_ms_since_boot(get_absolute_time()) + 15000;
while (!s_mqtt_connected) {
if (to_ms_since_boot(get_absolute_time()) > mqtt_deadline) {
printf("WARN: MQTT not connected after 15 s — discovery will be retried on reconnect\n");
break;
}
sleep_ms(100);
}
if (s_mqtt_connected) publish_discovery_all();
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD); /* primer */
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
double total_wh = 0.0;
while (true) {
sleep_ms(60 * 1000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
total_wh += (double)avg_p * dt_s / 3600.0;
t_prev_ms = t_now_ms;
/* Live RT values for the state payload. */
float u = 0, i_ = 0, pf = 0, q = 0;
uint8_t freq = 0;
rbamp_io_read_float_le(RB_ADDR, RB_REG_U_RMS, &u);
rbamp_io_read_float_le(RB_ADDR, RB_REG_I0_RMS, &i_);
rbamp_io_read_float_le(RB_ADDR, RB_REG_PF0, &pf);
rbamp_io_read_float_le(RB_ADDR, RB_REG_Q0, &q);
rbamp_io_read_u8 (RB_ADDR, RB_REG_AC_FREQ, &freq);
char payload[384];
int n = snprintf(payload, sizeof(payload),
"{"
"\"voltage\":%.1f,"
"\"current\":%.3f,"
"\"power\":%.1f,"
"\"energy\":%.3f,"
"\"frequency\":%u,"
"\"power_factor\":%.3f,"
"\"apparent_power\":%.1f,"
"\"reactive_power\":%.1f"
"}",
u, i_, avg_p, total_wh,
(unsigned)freq, pf, u * i_, q);
mqtt_publish(s_mqtt, "rbamp/" DEVICE_ID "/state", payload, n,
/*qos*/ 0, /*retain*/ 0, NULL, NULL);
printf("Published: %s\n", payload);
}
}
Exemplo 9 — Registador com bateria e sono dormente
Objetivo: um registador para exterior / fora da rede que acorda do modo dormente a cada 10 minutos através do alarme RTC, captura um período, publica via MQTT e volta ao modo dormente. O Pico W atinge algumas centenas de µA no modo dormente — suficiente para muitos meses numa célula de iões de lítio. Hardware: Pico W + um rbAmp UI1 + iões de lítio. O rbAmp pode ser desligado da alimentação através de um interruptor high-side no GPIO 16. Persistência: pico/sleep.h + o RTC do chip + uma pequena região NOINIT (ou NVM externa) para o estado que tem de sobreviver ao sono.
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "pico/sleep.h"
#include "hardware/rtc.h"
#include "hardware/gpio.h"
#include "lwip/apps/mqtt.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
#define PIN_RBAMP_POWER 16
#define WAKE_SECONDS (10 * 60)
extern void net_init(void);
extern mqtt_client_t *s_mqtt;
/* "NOINIT" region — variables that are not zeroed by the startup code.
* They survive dormant sleep on RP2040 because RAM stays powered. */
__attribute__((section(".uninitialized_data")))
static double s_total_wh;
__attribute__((section(".uninitialized_data")))
static uint32_t s_wake_count;
__attribute__((section(".uninitialized_data")))
static bool s_primer_done;
__attribute__((section(".uninitialized_data")))
static uint32_t s_magic; /* 0xCAFEFEED when state is initialised */
/**
* @brief Power-gate the rbAmp module.
*/
static void rbamp_power(bool on) {
gpio_init(PIN_RBAMP_POWER);
gpio_set_dir(PIN_RBAMP_POWER, GPIO_OUT);
gpio_put(PIN_RBAMP_POWER, on);
if (on) sleep_ms(300); /* let the LDO + MCU boot */
}
/**
* @brief Arm the RTC alarm `seconds` ahead (with day-wrap) and enter dormant sleep.
* @details Execution resumes at the reset vector via watchdog. On Pico W,
* deinit CYW43 BEFORE calling this — leaving the radio powered keeps
* the chip at ~10 mA instead of ~180 µA in dormant.
*/
static void enter_dormant(uint32_t seconds) {
datetime_t now;
if (!rtc_get_datetime(&now)) {
/* RTC not running — fall back to a brute reboot via watchdog. */
watchdog_reboot(0, 0, seconds * 1000U);
while (1) tight_loop_contents();
}
/* Convert "now" + `seconds` to absolute calendar time WITH day-wrap.
* Without this, alarms in the last 60 s of a day land at 00:0x today —
* a time in the past — and the RTC never matches until 24 h later. */
int total_sec = now.hour * 3600 + now.min * 60 + now.sec + (int)seconds;
int day_offset = total_sec / 86400;
total_sec %= 86400;
datetime_t alarm = now;
alarm.hour = total_sec / 3600;
alarm.min = (total_sec / 60) % 60;
alarm.sec = total_sec % 60;
if (day_offset > 0) {
/* Bump the day; for periods ≤ 24 h this is at most one day forward. */
alarm.day += day_offset;
/* NOTE: this does not handle month/year roll-over; for periods ≤ 24 h
* and well-set RTC the simplest fix is to step the day field; for a
* production logger use a proper time_t arithmetic via mktime. */
}
sleep_run_from_xosc();
sleep_goto_sleep_until(&alarm, NULL);
/* Force a clean reset so main() re-runs from the top (with NOINIT state). */
watchdog_reboot(0, 0, 1);
while (1) tight_loop_contents();
}
int main(void) {
stdio_init_all();
sleep_ms(1000);
/* Initialise persistent state on cold boot. Write `s_magic` LAST so a
* crash mid-init leaves the marker unset and forces re-initialisation. */
if (s_magic != 0xCAFEFEEDU) {
s_total_wh = 0.0;
s_wake_count = 0;
s_primer_done = false;
__dmb(); /* publish other fields before the marker */
s_magic = 0xCAFEFEEDU;
/* Seed the RTC with an arbitrary epoch so rtc_get_datetime() returns
* a valid struct from the first call. Without this, the alarm math in
* enter_dormant() reads garbage and sleep duration is undefined. */
rtc_init();
datetime_t epoch = { .year=2024, .month=1, .day=1,
.dotw=1, .hour=0, .min=0, .sec=0 };
rtc_set_datetime(&epoch);
sleep_us(64); /* RTC needs a few cycles to latch */
} else {
rtc_init();
}
s_wake_count++;
/* Power up rbAmp + I2C. */
rbamp_power(true);
rbamp_io_init(i2c0, 4, 5, 50000);
if (rbamp_io_wait_ready(RB_ADDR, 2000) != PICO_OK) {
printf("rbAmp not ready — sleeping\n");
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
/* First wake-up after a cold boot: primer snapshot only. */
if (!s_primer_done) {
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
s_primer_done = true;
printf("Primer done — entering dormant\n");
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
/* Subsequent wake-ups: close the period and read its average power. */
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
printf("Stale snapshot — skipping cycle\n");
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
/* dt approximation: dormant sleep + boot ≈ WAKE_SECONDS. For higher accuracy
* read the RTC calendar on entry and exit. */
float dt_s = (float)WAKE_SECONDS;
s_total_wh += (double)avg_p * dt_s / 3600.0;
/* Publish via Wi-Fi + MQTT (graceful fallback). */
net_init();
if (s_mqtt) {
char payload[256];
int n = snprintf(payload, sizeof(payload),
"{\"wake\":%lu,\"dt_s\":%.1f,\"avg_p\":%.1f,\"energy_wh\":%.3f}",
(unsigned long)s_wake_count, dt_s, avg_p, s_total_wh);
mqtt_publish(s_mqtt, "rbamp/remote/state", payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
printf("Published: %s\n", payload);
sleep_ms(200); /* let LwIP flush the publish */
} else {
printf("Wi-Fi/MQTT failed — value buffered in NOINIT RAM\n");
}
/* Power down the CYW43 radio BEFORE dormant — leaving it powered keeps
* the chip at ~10 mA instead of ~180 µA. Required for the headline
* "6 months on a 2000 mAh cell" power budget. */
#if PICO_CYW43_SUPPORTED
cyw43_arch_deinit();
#endif
rbamp_power(false);
enter_dormant(WAKE_SECONDS);
}
Notes:
- A secção
.uninitialized_datanão é inicializada a zero no arranque; sobrevive à breve reposição que se segue ao despertar do sono dormente. Um sentinela de número mágico (s_magic) permite distinguir um arranque a frio (RAM não inicializada, magic aleatório) de um despertar. - Para persistência permanente entre remoções da bateria, guarde periodicamente o total na flash interna com
flash_range_program(). O Pico SDK tem bons exemplos empico-examples/flash/. - Um Pico W em suspensão dormente, com o CYW43 desligado, fica em ~1 mA. O RP2040 sozinho (Pico) desce para ~180 µA. Use
cyw43_arch_deinit()antes de suspender, para desligar o módulo de rádio.
Exemplo 10 — Tarifa de tempo de uso (TOU) com relógio de parede SNTP
Objetivo: faturar energia segundo um horário de tempo de uso. O Pico W mantém um relógio de parede real via SNTP, distribui cada período fechado pelo escalão tarifário correto, repõe os totais diários à meia-noite e publica payloads com carimbos ISO. Hardware: Pico W + um rbAmp UI1 + Wi-Fi.
Acréscimos ao CMakeLists.txt:
target_link_libraries(example_10
pico_stdlib
hardware_i2c
pico_cyw43_arch_lwip_threadsafe_background
pico_lwip_mqtt
pico_lwip_sntp)
src/example_10.c:
#include
#include
#include
#include "pico/stdlib.h"
#include "pico/cyw43_arch.h"
#include "lwip/apps/mqtt.h"
#include "lwip/apps/sntp.h"
#include "rbamp_io.h"
#define RB_ADDR 0x50U
/* CEST = UTC+2. For full DST handling, recompute on roll-over. */
#define TZ_OFFSET_HOURS 2
#define PEAK_START_HOUR 8
#define PEAK_END_HOUR 22
extern void net_init(void);
extern mqtt_client_t *s_mqtt;
typedef struct {
double peak_wh, off_peak_wh;
int day_of_year;
} day_totals_t;
typedef struct {
double peak_wh, off_peak_wh;
} lifetime_totals_t;
static day_totals_t s_today = { .day_of_year = -1 };
static lifetime_totals_t s_lifetime = { 0 };
/**
* @brief Start SNTP and wait until the C library `time(NULL)` returns plausible UTC.
*/
static bool sntp_sync(uint32_t timeout_ms) {
sntp_setoperatingmode(SNTP_OPMODE_POLL);
sntp_setservername(0, "pool.ntp.org");
sntp_setservername(1, "time.google.com");
sntp_init();
absolute_time_t deadline = make_timeout_time_ms(timeout_ms);
while (!time_reached(deadline)) {
time_t now = time(NULL);
if (now > 1700000000) { /* ≥ year 2023 */
struct tm lt;
gmtime_r(&now, <);
printf("SNTP sync: %04d-%02d-%02d %02d:%02d:%02d UTC\n",
lt.tm_year + 1900, lt.tm_mon + 1, lt.tm_mday,
lt.tm_hour, lt.tm_min, lt.tm_sec);
return true;
}
sleep_ms(500);
}
return false;
}
static struct tm local_time(void) {
time_t now = time(NULL) + (TZ_OFFSET_HOURS * 3600);
struct tm lt;
gmtime_r(&now, <);
return lt;
}
static bool is_peak_hour(int hour) {
return (hour >= PEAK_START_HOUR) && (hour < PEAK_END_HOUR);
}
static void iso_now(char *out, size_t out_len) {
struct tm lt = local_time();
char sign = (TZ_OFFSET_HOURS >= 0) ? '+' : '-';
int off = (TZ_OFFSET_HOURS < 0) ? -TZ_OFFSET_HOURS : TZ_OFFSET_HOURS;
snprintf(out, out_len, "%04d-%02d-%02dT%02d:%02d:%02d%c%02d00",
lt.tm_year + 1900, lt.tm_mon + 1, lt.tm_mday,
lt.tm_hour, lt.tm_min, lt.tm_sec, sign, off);
}
/**
* @brief Add one period's energy to the right bucket; roll over the day at midnight.
*/
static void accumulate(double e_wh, const struct tm *tm_now) {
if (s_today.day_of_year != tm_now->tm_yday) {
if (s_today.day_of_year >= 0) {
char payload[192];
int n = snprintf(payload, sizeof(payload),
"{\"yday\":%d,\"peak_wh\":%.3f,\"off_peak_wh\":%.3f,"
"\"total_wh\":%.3f}",
s_today.day_of_year, s_today.peak_wh, s_today.off_peak_wh,
s_today.peak_wh + s_today.off_peak_wh);
mqtt_publish(s_mqtt, "rbamp/tou/day_close", payload, n,
/*qos*/ 1, /*retain*/ 1, NULL, NULL);
printf("Day closed: %s\n", payload);
}
s_today.peak_wh = 0.0;
s_today.off_peak_wh = 0.0;
s_today.day_of_year = tm_now->tm_yday;
}
if (is_peak_hour(tm_now->tm_hour)) {
s_today.peak_wh += e_wh;
s_lifetime.peak_wh += e_wh;
} else {
s_today.off_peak_wh += e_wh;
s_lifetime.off_peak_wh += e_wh;
}
}
int main(void) {
stdio_init_all();
sleep_ms(2000);
net_init();
sntp_sync(15000);
rbamp_io_init(i2c0, 4, 5, 50000);
rbamp_io_wait_ready(RB_ADDR, 2000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD); /* primer */
uint32_t t_prev_ms = to_ms_since_boot(get_absolute_time());
printf("TOU started: peak %02d:00..%02d:00 local\n",
PEAK_START_HOUR, PEAK_END_HOUR);
while (true) {
sleep_ms(60 * 1000);
rbamp_io_write_u8(RB_ADDR, RB_REG_COMMAND, RB_CMD_LATCH_PERIOD);
uint32_t t_now_ms = to_ms_since_boot(get_absolute_time());
sleep_ms(50);
uint8_t valid = 0;
rbamp_io_read_u8(RB_ADDR, RB_REG_PERIOD_VALID, &valid);
if ((valid & 0x01U) == 0) {
t_prev_ms = to_ms_since_boot(get_absolute_time());
continue;
}
float avg_p = 0.0f;
rbamp_io_read_float_le(RB_ADDR, RB_REG_PERIOD_AVG_P0, &avg_p);
float dt_s = (float)(t_now_ms - t_prev_ms) / 1000.0f;
double e_wh = (double)avg_p * dt_s / 3600.0;
t_prev_ms = t_now_ms;
struct tm lt = local_time();
if (lt.tm_year + 1900 < 2023) {
printf("WARN: clock not synced — retrying SNTP\n");
sntp_sync(15000);
continue;
}
accumulate(e_wh, <);
bool peak = is_peak_hour(lt.tm_hour);
char iso[40];
iso_now(iso, sizeof(iso));
char payload[384];
int n = snprintf(payload, sizeof(payload),
"{"
"\"ts\":\"%s\","
"\"tariff\":\"%s\","
"\"avg_p\":%.1f,"
"\"period_wh\":%.4f,"
"\"today_peak_wh\":%.3f,"
"\"today_off_peak_wh\":%.3f,"
"\"life_peak_wh\":%.3f,"
"\"life_off_peak_wh\":%.3f"
"}",
iso, peak ? "peak" : "off_peak",
avg_p, e_wh,
s_today.peak_wh, s_today.off_peak_wh,
s_lifetime.peak_wh, s_lifetime.off_peak_wh);
mqtt_publish(s_mqtt, "rbamp/tou/state", payload, n,
/*qos*/ 0, /*retain*/ 0, NULL, NULL);
printf("%s\n", payload);
}
}
Notes:
pico_lwip_sntpliga-se ao cliente SNTP do LwIP; o SDK liga-o aotime(NULL)da biblioteca C, para quegmtime_r()funcione logo à partida.- Para o tratamento completo do horário de verão, guarde o desfasamento TZ numa pequena tabela de consulta, ou incorpore uma string TZ POSIX através do mecanismo newlib
tzset(), se a sua compilação o incluir. - Para a medição bidirecional STD, chame
accumulate()duas vezes — uma para o consumo e outra para a exportação — e publique ambos os escalões de ponta e fora de ponta.
Comparação de exemplos
| # | Complexidade | Saída | MQTT | DRDY | Multi-módulo | Bidirecional | Persistência | Caso de utilização |
|---|---|---|---|---|---|---|---|---|
| 1 | mínimo | USB stdio | — | — | — | — | — | teste de funcionamento |
| 2 | baixo | OLED | — | — | — | — | RAM | contador em caixa |
| 3 | baixo | USB stdio | — | — | sim (3) | — | — | monitorização doméstica |
| 4 | médio | — | sim | — | — | — | RAM | por eletrodoméstico no HA |
| 5 | médio | USB stdio | — | sim | — | sim (mestre) | RAM | casa solar em nível BASIC |
| 6 | alta | — | sim | — | sim (3) | sim | RAM | balanço energético doméstico completo |
| 7 | médio | USB + SD (FATFS) | — | sim | — | — | Cartão SD | deteção de eventos |
| 8 | médio | — | sim (+disco) | — | — | opcional | RAM + MQTT | Auto-discovery do HA |
| 9 | médio | — | sim | — | — | — | RAM NOINIT | registador para exterior / fora da rede |
| 10 | médio | USB stdio | sim | — | — | opcional | RAM + MQTT | TOU pico/fora de pico com SNTP |
Boas práticas
- Verifique sempre os códigos de retorno das chamadas
rbamp_io_*. As transações I²C podem falhar em barramentos longos; o código de produção deve repetir em vez de ignorar. - Mantenha os callbacks de IRQ de GPIO mínimos. O Pico SDK usa um único callback partilhado para todas as IRQs de GPIO — defina uma flag
volatile boole retorne. Todo o trabalho de I²C / printf pertence ao ciclo principal. - Use o
i2c0e oi2c1de forma independente. rbAmp emi2c0, OLED emi2c0, cartão SD em SPI — mantenha os periféricos no barramento para o qual foram inicializados. - Use
to_ms_since_boot(get_absolute_time())para o relógio mestre. Precisão de microssegundos viato_us_since_boot(). Monotónico, sobrevive asleep_ms(). PERIOD_VALID(0x07) tem de ser verificado após cadaCMD_LATCH_PERIOD. Os instantâneos desatualizados acontecem se o mestre consultar mais depressa do que o firmware integra.- Aguarde ≥ 50 ms depois de um instantâneo antes de ler
0xDC..0xEF. - Para configurações com vários módulos,
rbamp_io_broadcast_latch(tick, group)via chamada geral garante uma sincronização precisa. A receção de chamada geral é opt-in por módulo (FLEET_CONFIG.bit0, por defeito DESLIGADO). Em caso de NACK, recue para a captura sequencial por módulo. - Para aplicações com bateria no Pico W, desative o CYW43 (
cyw43_arch_deinit()) antes do sono para poupar vários mA. O modo dormente do RP2040 é de ~180 µA, e o do RP2350 é ainda mais baixo. - Guarde os totais de Wh na memória flash interna com
flash_range_program()se precisar que sobrevivam a uma perda total de energia. A RAM NOINIT sobrevive ao modo dormente, mas não a um corte de energia. - O suporte de float em
printfestá ativado por predefinição empico_stdlib. Para o RP2040 usa-se a implementaçãopico_floatdo SDK; para o RP2350 o suporte de FPU em hardware está ativo por predefinição.
O que se segue
Depois de percorrer estes dez exemplos:
- Para desenvolvimento ESP32 em estilo Arduino, veja arduino-examples.md (bruto).
- Para MicroPython / CircuitPython (incluindo no próprio Pico), veja micropython-examples.md (bruto).
- Para o ESP-IDF nativo, veja esp-idf-examples.md (em bruto).
- Para STM32 HAL, veja stm32-hal-examples.md.
- Para a integração ESPHome (YAML declarativo), veja
tools/esphome-rbamp/docs/en/. - A especificação formal dos registos I²C usada aqui está em api-reference.md.