Cosa costruirà
- Una riga CSV per intervallo —
timestamp, voltage, current, power, energy— aggiunta a un file su una scheda microSD. - Le stesse righe inviate via seriale, così può registrare direttamente su un PC (o su un plotter seriale) senza la scheda.
- Timestamp reali da un RTC DS3231 opzionale sul bus I²C — oppure l'uptime
millis()se non usa l'RTC. - Robusto contro una scheda mancante o una lettura errata — continua e segnala il problema invece di bloccarsi.
Distinta dei materiali
| Voce | Q.tà | Note |
|---|---|---|
| rbAmp BASIC SCT-UI1 | 1 | tensione + corrente + potenza reale a bordo · prodotto |
| TA SCT-013 | 1 | portata da adattare al suo circuito · prodotto |
| Scheda di sviluppo ESP32 (framework Arduino) | 1 | il target verificato in compilazione (portabile ad altre schede Arduino) |
| Modulo scheda microSD | 1 | SPI; una scheda formattata FAT |
| RTC DS3231 (opzionale) | 1 | timestamp reali dall'orologio; condivide il bus I²C (indirizzo 0x68). Richiede la libreria RTClib (Adafruit). Se la salta, le righe avranno come timestamp l'uptime. |
Lo cablili
Due bus, nessun conflitto:
-
I²C porta il modulo rbAmp (
0x50) — e l'RTC (0x68) se ne monta uno — su SDA/SCL. Alimenti il modulo a 5 V, massa comune; il bus è a logica 3.3 V (perché?). -
SPI porta il modulo microSD sui pin VSPI hardware dell'ESP32: SCK → GPIO18, MISO → GPIO19, MOSI → GPIO23, CS → GPIO5. Tenga i due bus sui loro pin — nessun conflitto con I²C.
I TA SCT-013 si stringono attorno al conduttore del circuito — non invasivi sul lato corrente.
Il CSV
A ogni intervallo il logger aggiunge una riga; l'intestazione viene scritta alla prima creazione del file:
timestamp,voltage_V,current_A,power_W,energy_Wh
2026-07-30 14:05:00,230.4,0.211,48.2,12.345
2026-07-30 14:05:30,230.1,0.208,47.6,12.477
(Con l'RTC montato ottiene date reali; senza, la colonna del timestamp mostra l'uptime up+.)
Lo apra con un qualsiasi foglio di calcolo o strumento di grafici — è solo testo.
Lo sketch
Imposti MY_CT, inserisca una scheda microSD e faccia il flash. ESP32 (framework Arduino) a 50 kHz; SD sui pin VSPI, RTC DS3231 sul bus I²C condiviso:
/**
* SdCsvLogger.ino — log energy to microSD as CSV (standalone, no network).
*
* One rbAmp module meters a circuit; every interval the Arduino writes a
* timestamped CSV row to a microSD card AND mirrors it over Serial (redirect to
* a file, or watch in a serial plotter). A data logger you own — no HA, no cloud.
*
* Columns: timestamp,voltage_V,current_A,power_W,energy_Wh
*
* Board: ESP32 (Arduino framework); I2C @ 50 kHz. Non-ESP32 host = 100 kHz.
* Timestamps: a DS3231 RTC on the SAME I2C bus (addr 0x68, coexists with rbAmp
* @0x50) gives real wall-clock time. No RTC -> millis() uptime.
* Wiring: I2C SDA->GPIO21 SCL->GPIO22; rbAmp VCC->5 V; DS3231 VCC->3.3 V; GND
* common; ~4.7 kOhm pull-ups to 3.3 V.
* SD (VSPI) SCK->GPIO18 MISO->GPIO19 MOSI->GPIO23 CS->GPIO5.
*
* Accuracy: per clamp rating — the class and the sensor's own tolerance are both in the accuracy table on the BASIC page.
*/
#include
#include
#include
#include
#include
/* ---- configuration — the reader edits these ------------------------------ */
static const uint8_t RBAMP_ADDR = 0x50;
static const uint8_t METER_CH = 0;
static const uint32_t I2C_HZ = 50000; /* ESP32-Arduino: 50 kHz */
static const uint8_t SD_CS = 5; /* microSD chip-select (VSPI default) */
static const char* CSV_PATH = "/energy.csv";
static const uint32_t LOG_MS = 30000; /* one CSV row every 30 s */
/* Match to your clamp: Sct013_005 / _010 / _030 / _050 / _020. */
static const RbAmpCTModel MY_CT = RbAmpCTModel::Sct013_030;
static const char CSV_HEADER[] = "timestamp,voltage_V,current_A,power_W,energy_Wh";
/* ---- state --------------------------------------------------------------- */
static RbAmp dev(Wire, RBAMP_ADDR, RbAmpTopology::Single);
static RTC_DS3231 rtc;
static bool rtc_ok = false;
static bool sd_ok = false;
static uint32_t next_log_ms = 0;
static uint32_t rows = 0, skipped = 0, sd_fail = 0;
/* Apply the CT model only if it differs (setCTModel() persists to flash). */
static void ensureCtModel() {
uint8_t applied = 0;
if (dev.readCTModelCh(METER_CH, applied) && applied == static_cast(MY_CT)) {
return;
}
Serial.println(F("configuring CT model (persists to flash)..."));
if (!dev.setSensorClass(RbAmpSensorClass::Sct013) || !dev.setCTModel(MY_CT)) {
Serial.print(F("CT config failed: "));
Serial.println(RbAmp::errorString(dev.lastError()));
}
}
/* Wall-clock from the RTC, or uptime if no RTC. Primitive args only. */
static void makeTimestamp(char* buf, size_t n) {
if (rtc_ok) {
DateTime now = rtc.now();
snprintf(buf, n, "%04u-%02u-%02u %02u:%02u:%02u",
now.year(), now.month(), now.day(),
now.hour(), now.minute(), now.second());
} else {
snprintf(buf, n, "up+%lus", static_cast(millis() / 1000UL));
}
}
/* Create the file with a header row the first time it doesn't exist. */
static void ensureHeader() {
if (!sd_ok || SD.exists(CSV_PATH)) return;
File f = SD.open(CSV_PATH, FILE_WRITE);
if (f) {
f.println(CSV_HEADER);
f.close();
Serial.print(F("created "));
Serial.println(CSV_PATH);
} else {
Serial.println(F("could not create CSV header on SD"));
}
}
/* Append one row: persist to SD (open/append/flush/close so a row is never
* lost on power-off) and mirror to Serial. Primitive args only. */
static void logRow(const char* ts, float v, float a, float p, double wh) {
char line[96];
snprintf(line, sizeof(line), "%s,%.1f,%.3f,%.1f,%.3f",
ts, v, a, p, wh);
Serial.println(line);
if (!sd_ok) return;
File f = SD.open(CSV_PATH, FILE_APPEND);
if (!f) {
sd_fail++;
if (sd_fail % 10 == 1)
Serial.println(F("SD append failed - still logging to Serial"));
return;
}
f.println(line);
f.flush();
f.close();
rows++;
}
/* ---- lifecycle ----------------------------------------------------------- */
void setup() {
Serial.begin(115200);
while (!Serial && millis() < 2000) {}
Wire.begin();
Wire.setClock(I2C_HZ);
/* rbAmp */
dev.setLogStream(&Serial);
uint8_t tries = 0;
while (!dev.begin()) {
Serial.print(F("rbAmp begin failed: "));
Serial.println(RbAmp::errorString(dev.lastError()));
if (++tries % 5 == 0)
Serial.println(F("check wiring: SDA/SCL/5V/GND + external pull-ups"));
delay(1000);
}
Serial.println(F("rbAmp online"));
ensureCtModel();
/* RTC (optional) */
rtc_ok = rtc.begin();
if (rtc_ok) {
if (rtc.lostPower()) {
/* First power-up / dead backup cell: seed from build time. Replace
* with a known-good time or a set-clock sketch for real accuracy. */
rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));
Serial.println(F("RTC lost power - seeded from build time (set it properly)"));
}
Serial.println(F("timestamp source: DS3231 RTC"));
} else {
Serial.println(F("no DS3231 RTC - timestamps fall back to millis() uptime"));
}
/* SD (optional) */
sd_ok = SD.begin(SD_CS);
if (sd_ok) {
ensureHeader();
} else {
Serial.println(F("no SD card - logging to Serial only"));
}
Serial.println(CSV_HEADER); /* so the Serial stream is a self-describing CSV too */
next_log_ms = millis();
}
void loop() {
uint32_t now = millis();
if (static_cast(now - next_log_ms) < 0) {
delay(5);
return;
}
next_log_ms = now + LOG_MS;
/* Latch a period so energy().wh() advances for this row. A stale period is
* noted but not fatal — the row still carries the live V/I/P + the current
* Wh total (energy simply does not advance that interval). */
RbAmpPeriodSnapshot snap;
if (!dev.readPeriodSnapshot(snap)) {
Serial.print(F("period stale/failed: "));
Serial.println(RbAmp::errorString(dev.lastError()));
}
float v = dev.readVoltage();
float a = dev.readCurrent(METER_CH);
float p = dev.readPower(METER_CH);
/* Skip the row on a transient bad read rather than write garbage. */
if (isnan(v) || isnan(a) || isnan(p)) {
skipped++;
Serial.println(F("skip row - transient bad read"));
return;
}
char ts[24];
makeTimestamp(ts, sizeof(ts));
logRow(ts, v, a, p, dev.energy().wh(METER_CH));
}
(Verificato in compilazione su ESP32 con Arduino-CLI — RbAmp + RTClib + i SD/SPI/Wire inclusi. Ogni riga viene aperta, scritta, sottoposta a flush e chiusa subito, così una riga non va mai persa per un buffer non scaricato allo spegnimento. L'RTC DS3231 e rbAmp condividono il bus I²C; la scheda SD è su pin SPI separati.)
Cosa fa lo sketch
Tre piccoli helper si occupano del logging — makeTimestamp(), ensureHeader() e logRow() — e loop() li collega alle letture del misuratore.
makeTimestamp() — ora reale, oppure uptime
if (rtc_ok) snprintf(buf, n, "%04u-%02u-%02u %02u:%02u:%02u", now.year(), ...);
else snprintf(buf, n, "up+%lus", millis()/1000UL);
Se all'avvio viene trovato un DS3231 (rtc.begin()), le righe ricevono un timestamp reale dell'orologio; se no, ricorrono all'uptime up+ e lo sketch lo segnala sulla seriale. In ogni caso il CSV è valido — senza RTC si perdono solo le date assolute.
ensureHeader() e logRow() — il percorso di scrittura CSV
File f = SD.open(CSV_PATH, FILE_APPEND);
f.println(line);
f.flush();
f.close(); // open -> append -> flush -> close, every single row
ensureHeader() scrive l'intestazione delle colonne una sola volta, solo quando il file viene creato per la prima volta. logRow() formatta una riga e fa la cosa importante: apre il file in modalità append, scrive la riga, poi esegue flush e chiude subito. Quell'apertura/flush/chiusura per riga è deliberata — la riga è sulla scheda nell'istante in cui viene scritta, quindi togliere la corrente (o la scheda) non perde mai dati in buffer. La stessa riga va prima a Serial.println(), così il flusso seriale è un CSV autodescrittivo che può reindirizzare direttamente su un file del PC.
loop() — leggi, proteggi, registra
dev.readPeriodSnapshot(snap); // latch a window so energy().wh() advances
float v = dev.readVoltage(); float a = dev.readCurrent(0); float p = dev.readPower(0);
if (isnan(v) || isnan(a) || isnan(p)) { skipped++; return; } // skip a bad read, don't log garbage
makeTimestamp(ts, sizeof(ts));
logRow(ts, v, a, p, dev.energy().wh(0));
Ogni LOG_MS (30 s) fa il latch di un periodo di misura così che il totale in wattora avanza, legge V/I/P live e — se nessuna è tornata NaN — applica il timestamp e scrive la riga. Una lettura errata transitoria viene saltata invece di scritta come spazzatura; un periodo non aggiornato viene annotato ma la riga viene comunque scritta (con V/I/P live e i Wh attuali), perché scartare un intero campione per un passo di energia non aggiornato sarebbe peggio.
Uso dei dati
Inserisca la scheda in un PC e apra il CSV in un foglio di calcolo — tracci la potenza nel corso della giornata, sommi l'energia per ora, individui i cicli del frigorifero o il ciclo di lavoro dello scaldabagno. Poiché la colonna energia è costituita da wattora reali integrati dall'host, i totali corrispondono a ciò che si aspetterebbe in bolletta. Preferisce un grafico in tempo reale invece che a posteriori? Lo porti in Home Assistant — ma per un registro completamente offline, questo file è suo.
Lo personalizzi
-
Più colonne — il modulo fornisce anche fattore di potenza e frequenza; li aggiunga a
CSV_HEADERe alla stringa di formato dilogRow. -
File giornalieri — inizi un nuovo file al giorno (
/2026-07-30.csv) dalla data dell'RTC, così un log non cresce senza limite. -
Imposti l'orologio correttamente — l'RTC prende l'ora dalla build alla prima accensione; aggiunga una riga
rtc.adjust()con un'ora nota, oppure si sincronizzi via NTP se mette l'ESP32 sul Wi-Fi. -
Più circuiti — registri una riga per modulo per intervallo combinando con la build multi-modulo.
-
Lo porti in un server — su un ESP32 può anche inviare ogni riga via POST a un server o pubblicarla via MQTT, mantenendo la scheda SD come backup offline.
La serie Arduino, riepilogo
Ora ha l'intero kit autonomo — senza bisogno di rete:
- Lo legga — un modulo su un OLED.
- Lo scali — più circuiti su un bus, in modo coerente.
- Agisca — faccia scattare un relè per sovracorrente.
- Registri — questa build, su SD/CSV.