rbAmp
ES
Tienda
Docs
Actualizado

10 · Ejemplos de Arduino

Este capítulo reúne bocetos Arduino completos y funcionales para escenarios típicos de rbAmp. Todos los ejemplos usan los auxiliares presentados en initialization.md.

Nota

Estos ejemplos hablan directamente con rbAmp mediante la API de registros I²C en bruto. Están pensados para integraciones nativas, embebidas o con recursos limitados, donde hace falta control directo y cada byte del bus importa.

La detección de reinicios del módulo (caídas de tensión, watchdog) se explica una sola vez para todas las plataformas en period-metering.md → Detecting a module restart; añádala a cualquier sketch de larga ejecución de los que siguen.

Para una interfaz más cómoda y estructurada, use la biblioteca Arduino rbamp (véase la tabla de bibliotecas cliente del README). La biblioteca encapsula los detalles de registro en una clase RbAmp de alto nivel con métodos con nombre (readVoltage(), latchPeriod(), readPeriodSnapshot(), etc.), un acumulador de Wh automático por canal, la disciplina de reintento + comprobación de cordura de la SPEC §B.5 para objetivos ESP32 y auxiliares multimódulo. La mayoría de los proyectos de usuario deben partir de la biblioteca y recurrir a la API en bruto solo cuando haga falta.

Índice de ejemplos

# Título Dificultad Pantalla / salida MQTT DRDY Multimódulo Bidireccional Caso de uso
1 Lectura rápida mínimo Serie — — — — Prueba de humo
2 Medidor de energía de 60 segundos en OLED bajo OLED — — — — Contador Wh encapsulado
3 Monitor multimódulo bajo Serie — — sí (3) — Monitorización de toda la vivienda
4 Medidor de energía por aparato (UI3) medio — sí — — — Submedición en HA
5 Contabilidad bidireccional en el maestro con un módulo BASIC medio Serie — sí — sí (maestro) Vivienda solar en nivel BASIC
6 Balance energético de la vivienda alta — sí — sí (3) sí Balance energético de la vivienda
7 Detección de eventos de corriente medio Serie + SD — sí — — Registro de eventos de electrodomésticos
8 Publicador MQTT con auto-descubrimiento de HA medio — sí (+disco) — — opcional Integración de HA lista para usar
9 Registrador remoto alimentado por batería con sueño profundo medio — sí — — — Medidor exterior / autónomo
10 Tarifa por franjas horarias (TOU) con hora de pared por NTP medio Serie sí — — opcional Medición por tarifa punta / valle

Cabecera común para todos los ejemplos

Cada ejemplo supone que las siguientes definiciones auxiliares están presentes en el archivo. Para ahorrar espacio, el bloque no se repite en cada boceto de abajo: considérelo incluido.

C++
#include 

/**
 * @brief  Read one byte from a register of an rbAmp slave.
 * @param  addr 7-bit I2C slave address.
 * @param  reg  Register address inside the slave.
 * @return Register value.
 */
uint8_t rb_read_u8(uint8_t addr, uint8_t reg) {
  Wire.beginTransmission(addr);
  Wire.write(reg);
  // Return 0 (not 0xFF) on NACK so bit-flags like DATA_VALID/PERIOD_VALID
  // are not falsely read as "valid" when the slave is unreachable.
  if (Wire.endTransmission(false) != 0) return 0;   // NACK on address/data
  if (Wire.requestFrom(addr, (uint8_t)1) != 1) return 0;
  return Wire.read();
}

/**
 * @brief  Read a little-endian float32 from four consecutive registers.
 * @details rbAmp supports READ auto-increment (burst-read is valid). The
 *          per-byte form below is shown for clarity; production code may
 *          prefer a single burst-read for atomicity (see chapter 11).
 * @param  addr 7-bit I2C slave address.
 * @param  reg  Address of the LSB of the 4-byte float.
 * @return Reconstructed IEEE-754 single-precision value.
 */
float rb_read_float_le(uint8_t addr, uint8_t reg) {
  uint8_t buf[4];
  for (int i = 0; i < 4; i++) buf[i] = rb_read_u8(addr, reg + i);
  float f;
  memcpy(&f, buf, 4);                          // host is little-endian (AVR/ESP/ARM)
  return f;
}

/**
 * @brief  Write a single byte to a register of an rbAmp slave.
 * @param  addr 7-bit I2C slave address.
 * @param  reg  Target register address.
 * @param  val  Byte to write.
 */
void rb_write_u8(uint8_t addr, uint8_t reg, uint8_t val) {
  Wire.beginTransmission(addr);
  Wire.write(reg);
  Wire.write(val);
  Wire.endTransmission();
}

/**
 * @brief  Broadcast CMD_LATCH_PERIOD to every rbAmp on the bus that has
 *         GC reception enabled (FLEET_CONFIG.bit0 = 1; opt-in, default OFF).
 * @details Canonical 5-byte general-call frame: A5 27 group tick_lo tick_hi.
 *          Slaves reject any first byte != 0xA5. See chapter 11 §6.3.2.
 * @param  tick16  Caller's 16-bit window counter — mirrored at GC_TICK
 *                 (0x59) for missed-frame detection.
 * @param  group   GROUP_ID filter (0 = all-call; otherwise must match
 *                 the module's REG_GROUP_ID = 0x28).
 * @return true on ACK (at least one slave accepted the frame).
 *         false on bus-level NACK — no module on the bus has GC enabled
 *         (or no module is in the group). Caller MUST fall back to
 *         per-module sequential CMD_LATCH_PERIOD.
 */
bool rb_broadcast_latch(uint16_t tick16, uint8_t group = 0) {
  Wire.beginTransmission(0x00);                // I2C general call
  Wire.write(0xA5);                            // frame magic
  Wire.write(0x27);                            // CMD_LATCH_PERIOD opcode
  Wire.write(group);                           // group_id
  Wire.write((uint8_t)(tick16 & 0xFF));        // tick_lo
  Wire.write((uint8_t)((tick16 >> 8) & 0xFF)); // tick_hi
  return Wire.endTransmission() == 0;
}

Ejemplo 1: lectura rápida (mínimo)

Objetivo: imprimir la U, I, P, PF actuales por Serial cada segundo. Hardware: ESP32 / Arduino + un rbAmp UI1.

C++
#define RB_ADDR 0x50

void setup() {
  Serial.begin(115200);
  Wire.begin();
  Wire.setClock(50000);
  delay(300);                                  // let the module finish booting

  // Wait until the first RT window has been computed (DATA_VALID bit 0).
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);
  Serial.println("rbAmp ready");
}

void loop() {
  // Real-time block at 0x86..0xBD is refreshed every ~100 ms by the module (200 ms before fw v1.2).
  float u  = rb_read_float_le(RB_ADDR, 0x86);  // RMS voltage,   V
  float i  = rb_read_float_le(RB_ADDR, 0x8E);  // RMS current,   A
  float p  = rb_read_float_le(RB_ADDR, 0xA6);  // active power,  W (signed)
  float pf = rb_read_float_le(RB_ADDR, 0xB2);  // power factor,  −1..+1 (signed)

  Serial.printf("U=%.1fV  I=%.3fA  P=%+.1fW  PF=%+.3f\n", u, i, p, pf);
  delay(1000);
}

Salida esperada:

Text
rbAmp ready
U=230.1V  I=0.262A  P=+60.2W  PF=+0.998
U=229.9V  I=0.262A  P=+60.1W  PF=+0.998
...

Ejemplo 2: medidor de energía de 60 segundos en OLED

Objetivo: contador Wh actualizado una vez por minuto, mostrado en una OLED de 128×64. Hardware: ESP32 + rbAmp + OLED SSD1306 en el mismo bus I²C. Contabilidad: unidireccional (nivel BASIC).

C++
#include 
#define RB_ADDR 0x50
#define OLED_W 128
#define OLED_H 64
Adafruit_SSD1306 oled(OLED_W, OLED_H, &Wire);

uint32_t t_prev_ms = 0;                        // wall-clock at last snapshot
double total_wh = 0;                           // accumulated energy, Wh

void setup() {
  Serial.begin(115200);
  Wire.begin();
  delay(300);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);

  // Wait DATA_VALID, then issue a primer snapshot (its result is discarded).
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);
  rb_write_u8(RB_ADDR, 0x01, 0x27);            // CMD_LATCH_PERIOD — primer
  t_prev_ms = millis();
}

void loop() {
  delay(60000);                                // 60-second period

  // 1) Final snapshot — closes the period [t_prev_ms .. now].
  rb_write_u8(RB_ADDR, 0x01, 0x27);
  uint32_t t_now_ms = millis();
  delay(50);                                   // let firmware finalise the snapshot

  // 2) Verify the snapshot is fresh before using it.
  if ((rb_read_u8(RB_ADDR, 0x07) & 0x01) == 0) {
    Serial.println("WARN: stale snapshot");
    t_prev_ms = millis();
    return;
  }

  // 3) Read time-averaged power for channel 0 (PERIOD_AVG_P_W[0]).
  float avg_p = rb_read_float_le(RB_ADDR, 0xDC);

  // 4) Compute energy using the MASTER clock (authoritative).
  float dt_s = (t_now_ms - t_prev_ms) / 1000.0f;
  double e_wh = (double)avg_p * dt_s / 3600.0;
  total_wh += e_wh;
  t_prev_ms = t_now_ms;

  // 5) Update the OLED.
  oled.clearDisplay();
  oled.setTextSize(1);
  oled.setTextColor(SSD1306_WHITE);
  oled.setCursor(0, 0);
  oled.printf("P:  %6.1f W", avg_p);
  oled.setCursor(0, 16);
  oled.printf("dt: %6.1f s", dt_s);
  oled.setCursor(0, 32);
  oled.setTextSize(2);
  oled.printf("%.2f Wh", total_wh);
  oled.display();

  Serial.printf("avg_P=%.1f  E_period=%.3f  total=%.3f\n", avg_p, e_wh, total_wh);
}

La OLED comparte el bus I²C de rbAmp (la dirección típica de la OLED es 0x3C, sin colisión con 0x50).


Ejemplo 3: monitor multimódulo

Objetivo: sondear tres módulos (alimentación principal, calentador de agua, AC) e imprimir la potencia total. Hardware: ESP32 + 3 × rbAmp UI1 (direcciones 0x50, 0x51, 0x52).

C++
const uint8_t modules[] = {0x50, 0x51, 0x52};
const char* labels[]    = {"Mains ", "Boiler", "AC    "};
const int N = 3;

void setup() {
  Serial.begin(115200);
  Wire.begin();
  Wire.setClock(50000);
  delay(300);

  // Bus scan — confirm every module is present.
  for (int i = 0; i < N; i++) {
    Wire.beginTransmission(modules[i]);
    if (Wire.endTransmission() != 0) {
      Serial.printf("ERROR: %s at 0x%02X not found — restarting in 5 s\n",
                    labels[i], modules[i]);
      delay(5000);
      ESP.restart();                           // reboot rather than hang
    }
  }
  Serial.println("All modules OK");
}

void loop() {
  float total_p = 0;
  Serial.println("---");

  // Read each module in turn (round-robin).
  for (int i = 0; i < N; i++) {
    float u = rb_read_float_le(modules[i], 0x86);
    float p = rb_read_float_le(modules[i], 0xA6);
    Serial.printf("[%s] U=%.1f  P=%+.1f W\n", labels[i], u, p);
    total_p += p;
  }
  Serial.printf("TOTAL: %.1f W\n", total_p);
  delay(2000);
}

Ejemplo 4: medidor de energía por aparato (UI3)

Objetivo: un módulo UI3 con tres pinzas de corriente CT en tres cargas monofásicas distintas. Contadores Wh independientes por carga. Publicación por MQTT. Hardware: ESP32 + 1 × rbAmp UI3. Contabilidad: unidireccional.

C++
#include 
#include 

#define RB_ADDR 0x50
const char* CH_NAMES[3] = {"main", "heatpump", "lights"};

WiFiClient espClient;
PubSubClient mqtt(espClient);

uint32_t t_prev_ms = 0;
double total_wh[3] = {0, 0, 0};                 // per-channel accumulated energy

/**
 * @brief  Publish a single channel's data to MQTT.
 * @param  ch_name   Channel name (used in the topic).
 * @param  avg_p     Time-averaged power over the closed period, W.
 * @param  e_wh      Accumulated channel energy, Wh.
 */
void mqtt_publish(const char* ch_name, float avg_p, double e_wh) {
  char topic[64], payload[64];
  snprintf(topic, sizeof(topic), "rbamp/%s/state", ch_name);
  snprintf(payload, sizeof(payload),
           "{\"power\":%.1f,\"energy\":%.4f}", avg_p, e_wh);
  mqtt.publish(topic, payload);
}

void setup() {
  Serial.begin(115200);
  WiFi.begin("ssid", "password");
  uint32_t wifi_start = millis();
  while (WiFi.status() != WL_CONNECTED) {        // bounded wait — avoid WDT
    delay(500);
    if (millis() - wifi_start > 30000) {
      Serial.println("WiFi timeout — restarting");
      ESP.restart();
    }
  }
  mqtt.setServer("192.168.1.10", 1883);
  mqtt.setKeepAlive(60);                         // 60 s keepalive (default 15 s)
  mqtt.connect("rbamp-ui3");                     // best-effort; loop() retries

  Wire.begin();
  delay(300);
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);
  rb_write_u8(RB_ADDR, 0x01, 0x27);             // primer snapshot
  t_prev_ms = millis();
}

void loop() {
  // Service MQTT keepalive every iteration (not once per 60 s — broker would
  // drop the session after the default 15 s timeout). Reconnect with bounded
  // back-off when the broker is unreachable.
  if (!mqtt.connected()) {
    static uint32_t last_retry = 0;
    if (millis() - last_retry > 5000) {
      last_retry = millis();
      mqtt.connect("rbamp-ui3");
    }
  }
  mqtt.loop();

  // Non-blocking 60-second period — keeps mqtt.loop alive for keepalive.
  static uint32_t last_period_ms = 0;
  if (last_period_ms == 0) last_period_ms = millis();
  if (millis() - last_period_ms < 60000) {
    delay(50);
    return;
  }
  last_period_ms = millis();

  // Snapshot + read three per-channel period averages.
  rb_write_u8(RB_ADDR, 0x01, 0x27);
  uint32_t t_now = millis();
  delay(50);

  if ((rb_read_u8(RB_ADDR, 0x07) & 0x01) == 0) {
    t_prev_ms = millis();
    return;
  }

  // Per-channel PERIOD_AVG_P_W: I0 at 0xDC, I1 at 0xC2, I2 at 0xC6.
  float avg_p[3];
  avg_p[0] = rb_read_float_le(RB_ADDR, 0xDC);   // I0
  avg_p[1] = rb_read_float_le(RB_ADDR, 0xC2);   // I1
  avg_p[2] = rb_read_float_le(RB_ADDR, 0xC6);   // I2

  float dt_s = (t_now - t_prev_ms) / 1000.0f;
  t_prev_ms = t_now;

  for (int ch = 0; ch < 3; ch++) {
    double e = (double)avg_p[ch] * dt_s / 3600.0;
    total_wh[ch] += e;
    Serial.printf("[%s] avg_P=%+.1f W  E_total=%.3f Wh\n",
                  CH_NAMES[ch], avg_p[ch], total_wh[ch]);
    mqtt_publish(CH_NAMES[ch], avg_p[ch], total_wh[ch]);
  }
}

Ejemplo 5: contabilidad bidireccional en el maestro para un módulo BASIC

Objetivo: implementar la contabilidad bidireccional en el maestro cuando el nivel del módulo es BASIC (el acumulador de periodos recorta las muestras negativas). El maestro lee el P_real en tiempo real en cada ventana de medición (~100 ms, v1.2 y posteriores) y separa él mismo consumo y exportación. Hardware: ESP32 + rbAmp UI1 en una carga con inversor solar. Aplicabilidad: para propietarios de BASIC que necesitan ver la exportación. Funciona hoy en módulos BASIC.

C++
#define RB_ADDR 0x50
const int PIN_DRDY = 15;

volatile bool data_ready = false;               // set by DRDY ISR
double e_consumed_wh = 0;
double e_exported_wh = 0;
uint32_t t_last_sample_ms = 0;

/**
 * @brief  Interrupt service routine for DRDY falling edge.
 * @details Marks fresh data available. Kept tiny (no I2C calls inside ISR).
 */
void IRAM_ATTR on_drdy() { data_ready = true; }

void setup() {
  Serial.begin(115200);
  Wire.begin();
  pinMode(PIN_DRDY, INPUT_PULLUP);
  delay(300);
  // Wait for the slave to come online BEFORE arming the ISR — otherwise a
  // settling pull-up edge can fire a spurious interrupt against a not-yet-
  // initialised slave and set data_ready before the first valid window.
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);
  t_last_sample_ms = millis();
  attachInterrupt(digitalPinToInterrupt(PIN_DRDY), on_drdy, FALLING);
  Serial.println("Bidirectional accumulator started");
}

void loop() {
  if (!data_ready) return;                      // sleep until next RT window
  data_ready = false;

  uint32_t t_now = millis();

  // Signed instantaneous P_real: positive = consume, negative = export.
  float p = rb_read_float_le(RB_ADDR, 0xA6);
  float dt_s = (t_now - t_last_sample_ms) / 1000.0f;
  t_last_sample_ms = t_now;

  // Split into two accumulators on the master side.
  if (p > 0) {
    e_consumed_wh += p * dt_s / 3600.0;
  } else {
    e_exported_wh += (-p) * dt_s / 3600.0;
  }

  // Print summary every 5 seconds (not on every RT window).
  static uint32_t last_print = 0;
  if (t_now - last_print >= 5000) {
    last_print = t_now;
    Serial.printf("P=%+8.1fW   consumed=%.4f Wh  exported=%.4f Wh  net=%+.4f Wh\n",
                  p, e_consumed_wh, e_exported_wh,
                  e_consumed_wh - e_exported_wh);
  }
}

Notes:

  • DRDY sincroniza las lecturas con cada ventana RT (~100 ms, v1.2 y posteriores).
  • La precisión depende de la estabilidad del intervalo DRDY (típicamente ±1 ms).
  • Se acumula un pequeño error cerca de los cruces por cero de P, pero es despreciable para las cargas domésticas.

Ejemplo 6: balance energético del hogar

Objetivo: panel de balance energético completo. Tres módulos:

  • rbAmp n.º 1 en la acometida principal (red): bidireccional, mide la entrada y la salida de la red.
  • rbAmp n.º 2 en la salida del inversor solar (solar): mide la generación.
  • rbAmp n.º 3 UI3 en tres cargas grandes (bomba de calor, aire acondicionado, cargador de VE).

El maestro calcula: total_consumed = solar_self_used + grid_consumed, solar_generated = solar_self_used + grid_exported.

Hardware: ESP32 + 3 × rbAmp + Wi-Fi + MQTT. Niveles: nivel STD para el módulo de red (bidireccional). Los módulos solar y de cargas pueden ser BASIC (unidireccionales por construcción).

C++
#include 
#include 

const uint8_t ADDR_MAINS = 0x50;                // bidirectional (STD)
const uint8_t ADDR_SOLAR = 0x51;                // generation only (BASIC OK)
const uint8_t ADDR_LOADS = 0x52;                // UI3, big consumers

// Bidirectional mains module (STD line)? Set true and fill the
// PERIOD_AVG_P_NEG address from the SKU datasheet. Keep false on BASIC.
const bool HAS_NEG_REG_MAINS = false;
#define REG_PERIOD_AVG_P_NEG_MAINS 0x00

WiFiClient espClient;
PubSubClient mqtt(espClient);

uint32_t t_prev_ms = 0;

/** Accumulated energy in Wh, per category. */
struct {
  double mains_in_wh    = 0;                    // grid consumed
  double mains_out_wh   = 0;                    // grid exported
  double solar_total_wh = 0;                    // solar generated
  double loads_wh[3]    = {0, 0, 0};            // per-appliance
} totals;

void setup() {
  Serial.begin(115200);
  WiFi.begin("ssid", "password");
  while (WiFi.status() != WL_CONNECTED) delay(500);
  mqtt.setServer("192.168.1.10", 1883);
  mqtt.connect("home-balance");

  Wire.begin();
  Wire.setClock(50000);
  delay(300);

  // Wait until all three modules report DATA_VALID.
  for (uint8_t addr : {ADDR_MAINS, ADDR_SOLAR, ADDR_LOADS}) {
    while ((rb_read_u8(addr, 0xCE) & 0x01) == 0) delay(50);
  }

  static uint16_t gc_tick = 0;
  if (!rb_broadcast_latch(gc_tick++)) {
    // GC NACK — no module has GC enabled. Fall back to per-module snapshot.
    for (uint8_t addr : {ADDR_MAINS, ADDR_SOLAR, ADDR_LOADS}) {
      rb_write_u8(addr, 0x01, 0x27);
    }
  }
  t_prev_ms = millis();
  Serial.println("Home balance started");
}

void loop() {
  delay(60000);

  // Synchronous snapshot — all three modules snapshot at the same instant.
  static uint16_t gc_tick = 1;
  if (!rb_broadcast_latch(gc_tick++)) {
    // GC NACK — fall back to per-module sequential snapshot (skew ~1 ms/module).
    for (uint8_t addr : {ADDR_MAINS, ADDR_SOLAR, ADDR_LOADS}) {
      rb_write_u8(addr, 0x01, 0x27);
    }
  }
  uint32_t t_now = millis();
  delay(50);

  float dt_s = (t_now - t_prev_ms) / 1000.0f;
  t_prev_ms = t_now;

  // ----- MAINS (bidirectional, STD line) -----
  if (rb_read_u8(ADDR_MAINS, 0x07) & 0x01) {
    float avg_p_consume = rb_read_float_le(ADDR_MAINS, 0xDC);
    float avg_p_export  = HAS_NEG_REG_MAINS
        ? rb_read_float_le(ADDR_MAINS, REG_PERIOD_AVG_P_NEG_MAINS)
        : 0.0f;
    totals.mains_in_wh  += avg_p_consume * dt_s / 3600.0;
    totals.mains_out_wh += avg_p_export  * dt_s / 3600.0;
  }

  // ----- SOLAR (generation only) -----
  // The CT arrow points toward the home; P > 0 = inverter exporting.
  if (rb_read_u8(ADDR_SOLAR, 0x07) & 0x01) {
    float avg_p = rb_read_float_le(ADDR_SOLAR, 0xDC);
    totals.solar_total_wh += avg_p * dt_s / 3600.0;
  }

  // ----- LOADS (UI3, three channels) -----
  if (rb_read_u8(ADDR_LOADS, 0x07) & 0x01) {
    float p[3];
    p[0] = rb_read_float_le(ADDR_LOADS, 0xDC);  // I0 channel
    p[1] = rb_read_float_le(ADDR_LOADS, 0xC2);  // I1 channel
    p[2] = rb_read_float_le(ADDR_LOADS, 0xC6);  // I2 channel
    for (int i = 0; i < 3; i++) totals.loads_wh[i] += p[i] * dt_s / 3600.0;
  }

  // Derived balance figures.
  double total_consumed  = totals.mains_in_wh + totals.solar_total_wh
                         - totals.mains_out_wh;
  double solar_self_used = totals.solar_total_wh - totals.mains_out_wh;
  if (solar_self_used < 0) solar_self_used = 0;  // clamp measurement noise

  Serial.printf("MAINS  in=%.2f  out=%.2f\n", totals.mains_in_wh, totals.mains_out_wh);
  Serial.printf("SOLAR  gen=%.2f  self-used=%.2f  exported=%.2f\n",
                totals.solar_total_wh, solar_self_used, totals.mains_out_wh);
  Serial.printf("LOADS  HP=%.2f  AC=%.2f  EV=%.2f\n",
                totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
  Serial.printf("TOTAL  household consumed=%.2f Wh\n", total_consumed);

  // Publish the entire balance to a single MQTT topic (retained).
  char payload[512];
  snprintf(payload, sizeof(payload),
    "{\"mains_in\":%.3f,\"mains_out\":%.3f,\"solar\":%.3f,"
    "\"self_used\":%.3f,\"total_consumed\":%.3f,"
    "\"hp\":%.3f,\"ac\":%.3f,\"ev\":%.3f}",
    totals.mains_in_wh, totals.mains_out_wh, totals.solar_total_wh,
    solar_self_used, total_consumed,
    totals.loads_wh[0], totals.loads_wh[1], totals.loads_wh[2]);
  mqtt.publish("home/energy/balance", payload, true);
  mqtt.loop();
}

Notes:

  • rb_broadcast_latch(tick) asegura que los tres módulos tomen la instantánea en el mismo instante, algo crítico para un balance preciso. La recepción GC es opcional por módulo (FLEET_CONFIG.bit0, por defecto desactivada; véase el capítulo 02). Si el marco GC recibe NACK, el ejemplo recurre a CMD_LATCH_PERIOD secuencial por módulo (desfase ~1 ms por módulo a 50 kHz).
  • solar_self_used = solar_total − exported_to_grid: la energía generada y consumida localmente.
  • total_consumed = mains_in + solar_self_used: consumo total del hogar.

Ejemplo 7: detección de eventos de corriente

Objetivo: en cada ventana RT (~100 ms, v1.2 y posteriores), comparar P con una media móvil exponencial ponderada (EMA). Registrar en una tarjeta SD las desviaciones significativas. Hardware: ESP32 + rbAmp + tarjeta SD. Caso de uso: detección automática de eventos de cargas grandes (microondas, aire acondicionado, hervidor) al encenderse o apagarse.

C++
#include 
#define RB_ADDR 0x50
const int PIN_DRDY  = 15;
const int PIN_SD_CS = 5;

volatile bool data_ready = false;
float p_ema = 0;                                // exponential moving average
const float EMA_ALPHA = 0.05;                   // ~2 s time constant at 10 Hz updates
const float EVENT_THRESHOLD_W = 200.0;          // ignore steps below this

File logfile;

/** @brief  DRDY interrupt — only sets a flag. */
void IRAM_ATTR on_drdy() { data_ready = true; }

void setup() {
  Serial.begin(115200);
  Wire.begin();
  pinMode(PIN_DRDY, INPUT_PULLUP);

  // SD card setup with explicit failure check — opening a non-existent file
  // returns a falsey File object; writing to it is undefined on some cores.
  if (!SD.begin(PIN_SD_CS)) {
    Serial.println("ERROR: SD.begin() failed — restarting in 5 s");
    delay(5000);
    ESP.restart();
  }
  logfile = SD.open("/events.log", FILE_APPEND);
  if (!logfile) {
    Serial.println("ERROR: SD.open(events.log) failed — restarting in 5 s");
    delay(5000);
    ESP.restart();
  }

  delay(300);
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);

  // Seed the EMA with the current power so we do not log a spurious startup event.
  p_ema = rb_read_float_le(RB_ADDR, 0xA6);
  attachInterrupt(digitalPinToInterrupt(PIN_DRDY), on_drdy, FALLING);
  Serial.println("Event detector started");
}

void loop() {
  if (!data_ready) return;
  data_ready = false;

  // Compute the deviation from the running average.
  float p = rb_read_float_le(RB_ADDR, 0xA6);
  float delta = p - p_ema;
  p_ema = (1 - EMA_ALPHA) * p_ema + EMA_ALPHA * p;

  // Log when the deviation exceeds the threshold.
  if (fabsf(delta) > EVENT_THRESHOLD_W) {       // fabsf for float (avoids double promotion)
    const char* type = (delta > 0) ? "TURN_ON" : "TURN_OFF";
    char line[128];
    snprintf(line, sizeof(line),
             "%lu  %s  delta=%+.1f W  P=%.1f W  EMA=%.1f W\n",
             millis(), type, delta, p, p_ema);
    Serial.print(line);
    logfile.print(line);
    logfile.flush();                            // ensure the line hits the card
  }
}

Notes:

  • La EMA se adapta a la carga de fondo en ~4 s: no reacciona a derivas lentas.
  • Un umbral de 200 W omite cargas menores (luces, cargadores de teléfono) y capta los electrodomésticos principales.
  • DRDY proporciona una sincronización precisa con cada actualización de P_real.

Ejemplo 8: publicador MQTT con descubrimiento automático de Home Assistant

Objetivo: una integración de HA lista para usar. El ESP32 se conecta a Wi-Fi y a un broker MQTT, publica las configuraciones de descubrimiento automático de Home Assistant (así las entidades aparecen en HA sin YAML) y emite un estado JSON cada minuto. No hacen falta cambios en el YAML de HA. Hardware: ESP32 + un rbAmp UI1 + red Wi-Fi con un broker MQTT (Mosquitto, EMQX, complemento Mosquitto de HA, etc.). Contabilidad: unidireccional. Sustituya los registros de periodo por los bidireccionales para los módulos STD.

C++
#include 
#include 

#define RB_ADDR 0x50
const char* WIFI_SSID    = "ssid";
const char* WIFI_PASS    = "password";
const char* MQTT_HOST    = "192.168.1.10";
const uint16_t MQTT_PORT = 1883;
const char* MQTT_USER    = "ha";                // optional, NULL to disable
const char* MQTT_PASS    = "secret";

// Stable identifiers — the HA discovery topic must be unique per entity.
const char* DEVICE_ID    = "rbamp_main";
const char* DEVICE_NAME  = "Mains rbAmp";

WiFiClient   espClient;
PubSubClient mqtt(espClient);

uint32_t t_prev_ms = 0;
double total_wh = 0;                            // accumulated energy

/**
 * @brief  Publish a single HA discovery config for one sensor.
 * @param  key          Short key used in topic and value_template.
 * @param  friendly     Friendly name shown in HA.
 * @param  unit         Unit of measurement (e.g. "V", "W", "Wh"). NULL = none.
 * @param  device_class HA device_class string (e.g. "voltage"). NULL = none.
 * @param  state_class  HA state_class ("measurement" / "total_increasing").
 * @details The config topic is retained, so HA discovers the entity even
 *          after a restart without waiting for the next state publish.
 */
void publish_discovery_sensor(const char* key,
                              const char* friendly,
                              const char* unit,
                              const char* device_class,
                              const char* state_class) {
  char topic[128];
  char payload[512];

  snprintf(topic, sizeof(topic),
           "homeassistant/sensor/%s/%s/config", DEVICE_ID, key);

  // Build the discovery JSON. The shared "device" block ties all entities
  // to one device card in HA.
  int n = snprintf(payload, sizeof(payload),
    "{"
      "\"name\":\"%s %s\","
      "\"unique_id\":\"%s_%s\","
      "\"state_topic\":\"rbamp/%s/state\","
      "\"value_template\":\"{{ value_json.%s }}\","
      "\"state_class\":\"%s\","
      "\"device\":{"
        "\"identifiers\":[\"%s\"],"
        "\"name\":\"%s\","
        "\"manufacturer\":\"rbAmp\","
        "\"model\":\"rbAmp UI*\""
      "}",
    DEVICE_NAME, friendly,
    DEVICE_ID, key,
    DEVICE_ID,
    key,
    state_class,
    DEVICE_ID, DEVICE_NAME);

  // Append optional fields.
  if (unit && n < (int)sizeof(payload)) {
    n += snprintf(payload + n, sizeof(payload) - n,
                  ",\"unit_of_measurement\":\"%s\"", unit);
  }
  if (device_class && n < (int)sizeof(payload)) {
    n += snprintf(payload + n, sizeof(payload) - n,
                  ",\"device_class\":\"%s\"", device_class);
  }
  if (n < (int)sizeof(payload) - 1) {           // guard against overflow underflow
    snprintf(payload + n, sizeof(payload) - n, "}");
  } else {
    payload[sizeof(payload) - 2] = '}';         // forced close on truncation
    payload[sizeof(payload) - 1] = '\0';
    Serial.println("WARN: HA discovery payload truncated");
  }

  mqtt.publish(topic, payload, true);           // retained — survives broker restart
}

/**
 * @brief  Publish the full HA Auto-discovery set for one rbAmp module.
 * @details Call once on every (re)connect to the broker.
 */
void publish_discovery_all() {
  publish_discovery_sensor("voltage",      "Voltage",       "V",  "voltage",      "measurement");
  publish_discovery_sensor("current",      "Current",       "A",  "current",      "measurement");
  publish_discovery_sensor("power",        "Power",         "W",  "power",        "measurement");
  publish_discovery_sensor("energy",       "Energy",        "Wh", "energy",       "total_increasing");
  publish_discovery_sensor("frequency",    "Frequency",     "Hz", "frequency",    "measurement");
  publish_discovery_sensor("power_factor", "Power Factor",  NULL, "power_factor", "measurement");
  publish_discovery_sensor("apparent_power", "Apparent Power", "VA",  "apparent_power", "measurement");
  publish_discovery_sensor("reactive_power", "Reactive Power", "var", "reactive_power", "measurement");
}

/**
 * @brief  Try to (re)connect to the MQTT broker once.
 * @return true on success, false otherwise. Caller is responsible for retry
 *         pacing — this function NEVER blocks longer than the underlying
 *         PubSubClient.connect() timeout.
 * @details Republishes discovery configs on every successful reconnect.
 *          Replaces the previous unbounded `while (!connected) delay(2000)`
 *          loop which would trip the ESP32 task watchdog after ~5 s of broker
 *          unavailability.
 */
bool mqtt_try_connect() {
  if (mqtt.connected()) return true;
  Serial.print("MQTT connecting... ");
  bool ok = MQTT_USER
      ? mqtt.connect(DEVICE_ID, MQTT_USER, MQTT_PASS)
      : mqtt.connect(DEVICE_ID);
  if (ok) {
    Serial.println("OK");
    publish_discovery_all();
  } else {
    Serial.printf("failed rc=%d (will retry)\n", mqtt.state());
  }
  return ok;
}

void setup() {
  Serial.begin(115200);

  // 1) WiFi — bounded wait, restart on persistent failure (avoids WDT).
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  uint32_t wifi_start = millis();
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    if (millis() - wifi_start > 30000) {
      Serial.println("WiFi timeout — restarting");
      ESP.restart();
    }
  }
  Serial.printf("WiFi up, IP=%s\n", WiFi.localIP().toString().c_str());

  // 2) MQTT.
  mqtt.setServer(MQTT_HOST, MQTT_PORT);
  mqtt.setKeepAlive(60);                        // 60 s keepalive (default 15 s)
  mqtt.setBufferSize(1024);                     // big enough for one discovery payload

  // 3) rbAmp.
  Wire.begin();
  Wire.setClock(50000);
  delay(300);
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);

  rb_write_u8(RB_ADDR, 0x01, 0x27);             // primer snapshot
  t_prev_ms = millis();

  // 4) First MQTT attempt — failure is non-fatal, loop() will retry.
  mqtt_try_connect();
}

void loop() {
  // Keep the broker session alive: service mqtt.loop() every iteration and
  // attempt reconnect with bounded back-off (no blocking 2s delay).
  if (!mqtt.connected()) {
    static uint32_t last_retry = 0;
    if (millis() - last_retry > 5000) {         // retry at most every 5 s
      last_retry = millis();
      mqtt_try_connect();
    }
  }
  mqtt.loop();

  static uint32_t last_period = 0;
  if (last_period == 0) last_period = millis(); // seed on first iteration
  if (millis() - last_period < 60000) {
    delay(50);                                  // short slice — keeps loop responsive
    return;
  }
  last_period = millis();

  // ----- Snapshot + read period snapshot -----
  rb_write_u8(RB_ADDR, 0x01, 0x27);
  uint32_t t_now = millis();
  delay(50);

  if ((rb_read_u8(RB_ADDR, 0x07) & 0x01) == 0) {
    Serial.println("WARN: stale snapshot, skipping publish");
    t_prev_ms = millis();
    return;
  }
  float avg_p = rb_read_float_le(RB_ADDR, 0xDC);
  float dt_s  = (t_now - t_prev_ms) / 1000.0f;
  total_wh += (double)avg_p * dt_s / 3600.0;
  t_prev_ms = t_now;

  // ----- Read live RT values -----
  float u  = rb_read_float_le(RB_ADDR, 0x86);
  float i  = rb_read_float_le(RB_ADDR, 0x8E);
  float pf = rb_read_float_le(RB_ADDR, 0xB2);
  float q  = rb_read_float_le(RB_ADDR, 0xD0);
  uint8_t freq = rb_read_u8(RB_ADDR, 0x20);

  // ----- Compose the state JSON -----
  char payload[384];
  snprintf(payload, sizeof(payload),
    "{"
      "\"voltage\":%.1f,"
      "\"current\":%.3f,"
      "\"power\":%.1f,"
      "\"energy\":%.3f,"
      "\"frequency\":%u,"
      "\"power_factor\":%.3f,"
      "\"apparent_power\":%.1f,"
      "\"reactive_power\":%.1f"
    "}",
    u, i, avg_p, total_wh,
    (unsigned)freq, pf, u * i, q);

  // Topic shape matches the value_template of every discovery config.
  char topic[64];
  snprintf(topic, sizeof(topic), "rbamp/%s/state", DEVICE_ID);
  mqtt.publish(topic, payload, false);          // state is fresh each period, not retained

  Serial.printf("Published: %s\n", payload);
}

Resultado en Home Assistant:

  • En cuanto llega la primera publicación, HA crea automáticamente un dispositivo llamado Mains rbAmp con 8 entidades (tensión, corriente, potencia, energía, frecuencia, factor de potencia, potencia aparente, potencia reactiva).
  • La entidad Energy tiene state_class: total_increasing y el device_class correcto, así que el panel de energía de HA la acepta como fuente de consumo.
  • Para eliminar la entidad de HA, publique una carga vacía en su tema homeassistant/sensor/.../config (retenido).

Extending:

  • Para UI2/UI3 multicanal, repita el bloque de descubrimiento con claves sufijadas (current_1, power_1, energy_1, …) y añada esos campos al JSON de estado.
  • Para los módulos STD bidireccionales, añada energy_exported con device_class: energy y state_class: total_increasing.

Ejemplo 9: registrador remoto alimentado por batería con sueño profundo

Objetivo: un registrador exterior / autónomo que se despierta cada 10 minutos, toma una instantánea de un periodo, publica los datos y vuelve al sueño profundo. El consumo medio es de un par de mA, por lo que una sola celda de Li-ion dura muchos meses. Hardware: ESP32 (o ESP32-S3) + un rbAmp UI1 + una pequeña batería de Li-ion + Wi-Fi. El rbAmp también se mantiene bajo un LDO de bajo reposo para que sus ~15 mA solo se consuman durante la vigilia. Contabilidad: unidireccional. La energía se conserva entre ciclos de sueño profundo mediante la memoria lenta RTC.

C++
#include 
#include 
#include "esp_sleep.h"

#define RB_ADDR 0x50

const char* WIFI_SSID = "ssid";
const char* WIFI_PASS = "password";
const char* MQTT_HOST = "192.168.1.10";

// Wake every 10 minutes (600 s). The interval is the master_dt for Wh.
const uint64_t SLEEP_US = 10ULL * 60ULL * 1000000ULL;

// Power for rbAmp can be gated through a MOSFET driven by a GPIO,
// or simply left always-on if the LDO quiescent is acceptable.
const int PIN_RBAMP_POWER = 4;

// Values that must survive deep sleep are placed in RTC slow memory.
// IMPORTANT: ESP32 RTC slow memory is NOT zeroed on power-on after a brown-out
// or PSU dropout — it may hold garbage that looks like valid state. Gate every
// retained variable through a magic-marker check on cold boot.
RTC_DATA_ATTR uint32_t rtc_magic         = 0;   // 0xCAFEFEED when state initialised
RTC_DATA_ATTR double   rtc_total_wh      = 0;
RTC_DATA_ATTR uint32_t rtc_wake_count    = 0;
RTC_DATA_ATTR bool     rtc_primer_done   = false;
RTC_DATA_ATTR uint64_t rtc_t_prev_us     = 0;   // boot-time wall-clock anchor

#define RTC_MAGIC 0xCAFEFEEDu

WiFiClient   espClient;
PubSubClient mqtt(espClient);

/**
 * @brief  Power rbAmp on/off via a GPIO-driven high-side switch.
 * @param  on  true = enable, false = disable.
 * @details If your hardware always-powers rbAmp, you can remove this function
 *          and skip the calls to it.
 */
void rbamp_power(bool on) {
  pinMode(PIN_RBAMP_POWER, OUTPUT);
  digitalWrite(PIN_RBAMP_POWER, on ? HIGH : LOW);
  if (on) delay(300);                           // boot time
}

/**
 * @brief  Bring up WiFi with a hard timeout, so deep-sleep is never blocked
 *         forever on a missing AP.
 * @param  timeout_ms  Maximum time to wait for an association.
 * @return true on success, false on timeout.
 */
bool wifi_connect(uint32_t timeout_ms) {
  WiFi.mode(WIFI_STA);
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  uint32_t t0 = millis();
  while (WiFi.status() != WL_CONNECTED) {
    if (millis() - t0 > timeout_ms) return false;
    delay(100);
  }
  return true;
}

/**
 * @brief  Publish one measurement to MQTT.
 * @param  avg_p   Time-averaged power over the last interval, W.
 * @param  total_e Accumulated energy total, Wh.
 * @param  dt_s    Length of the elapsed interval, seconds.
 */
void publish_measurement(float avg_p, double total_e, float dt_s) {
  char payload[256];
  snprintf(payload, sizeof(payload),
    "{\"wake\":%lu,\"dt_s\":%.1f,\"avg_p\":%.1f,\"energy_wh\":%.3f}",
    (unsigned long)rtc_wake_count, dt_s, avg_p, total_e);
  mqtt.publish("rbamp/remote/state", payload, true);
  mqtt.loop();
  Serial.printf("Published: %s\n", payload);
}

void setup() {
  Serial.begin(115200);

  // --- Cold-boot detection ---
  // On any non-deep-sleep reset (power-on, brown-out, watchdog, ESP.restart),
  // RTC slow memory may contain garbage. Initialise on first boot.
  if (rtc_magic != RTC_MAGIC) {
    Serial.println("Cold boot — initialising RTC state");
    rtc_total_wh    = 0.0;
    rtc_wake_count  = 0;
    rtc_primer_done = false;
    rtc_t_prev_us   = 0;
    rtc_magic       = RTC_MAGIC;
  }
  rtc_wake_count++;

  // --- Power up rbAmp and bring up I2C ---
  rbamp_power(true);
  Wire.begin();
  Wire.setClock(50000);
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);

  // First wake-up after a cold boot: do a primer snapshot (its result is discarded).
  if (!rtc_primer_done) {
    rb_write_u8(RB_ADDR, 0x01, 0x27);
    rtc_t_prev_us = esp_timer_get_time();
    rtc_primer_done = true;

    // Go straight back to sleep — we need at least one full period to elapse
    // before the next snapshot can produce a meaningful sample.
    Serial.println("Primer done — sleeping until first real period");
    rbamp_power(false);
    esp_sleep_enable_timer_wakeup(SLEEP_US);
    esp_deep_sleep_start();
  }

  // --- Subsequent wake-ups: read the period that just ended ---
  rb_write_u8(RB_ADDR, 0x01, 0x27);             // close current period
  uint64_t t_now_us = esp_timer_get_time();
  delay(50);

  if ((rb_read_u8(RB_ADDR, 0x07) & 0x01) == 0) {
    Serial.println("WARN: stale snapshot — skipping this cycle");
    rtc_t_prev_us = t_now_us;
    rbamp_power(false);
    esp_sleep_enable_timer_wakeup(SLEEP_US);
    esp_deep_sleep_start();
  }

  float avg_p = rb_read_float_le(RB_ADDR, 0xDC);
  // dt is wall-clock between snapshots; we measure it on the ESP32's RTC.
  // SLEEP_US is the intent; esp_timer accounts for actual sleep + on-time.
  float dt_s = (float)(t_now_us - rtc_t_prev_us) / 1000000.0f;
  rtc_t_prev_us = t_now_us;

  // Accumulate energy in RTC memory so it survives sleep.
  rtc_total_wh += (double)avg_p * dt_s / 3600.0;

  // --- Publish via WiFi/MQTT ---
  if (wifi_connect(8000)) {
    mqtt.setServer(MQTT_HOST, 1883);
    mqtt.setBufferSize(512);
    if (mqtt.connect("rbamp-remote")) {
      publish_measurement(avg_p, rtc_total_wh, dt_s);
      mqtt.disconnect();
    }
    WiFi.disconnect(true);
    WiFi.mode(WIFI_OFF);
  } else {
    Serial.println("WiFi failed — value buffered in RTC memory, will retry next wake");
  }

  // --- Sleep ---
  rbamp_power(false);                           // power-gate rbAmp
  esp_sleep_enable_timer_wakeup(SLEEP_US);
  Serial.println("Deep sleep");
  esp_deep_sleep_start();
}

void loop() {
  // setup() always ends in esp_deep_sleep_start() — loop is never reached.
}

Presupuesto de energía (típico, ESP32-WROOM):

  • Tiempo despierto por despertar: ~3 s (Wi-Fi + MQTT + I²C).
  • Corriente en vigilia: ~80 mA de media → ~0.07 mAh por despertar.
  • Corriente en reposo: ~10 µA (dominios RTC + retenidos).
  • Un despertar cada 10 min → ~10 mAh/día en total → una sola celda de Li-ion de 2000 mAh dura ~6 meses.

Notes:

  • rtc_total_wh sobrevive a la suspensión profunda mediante RTC_DATA_ATTR. Se pierde con un corte total de alimentación (batería retirada). Para una persistencia absoluta, guarde periódicamente el valor por MQTT o en NVS.
  • El paso de instantánea de cebado está condicionado por rtc_primer_done, así que la primera muestra tras un arranque en frío se descarta correctamente.
  • wifi_connect() tiene un tiempo de espera máximo. Si el Wi-Fi no está disponible, el boceto vuelve a dormir: el total de energía sigue acumulándose internamente y se publica en la siguiente conexión correcta.

Ejemplo 10: tarifa por franjas horarias (TOU) con hora de pared por NTP

Objetivo: facturar la energía según una tarifa por franjas horarias (tarifas distintas en horas punta y fuera de punta). El ESP32 mantiene un reloj de pared real mediante NTP, reparte cada periodo cerrado en el tramo tarifario correspondiente, reinicia los totales diarios a medianoche y publica cargas MQTT con marcas de tiempo ISO. Hardware: ESP32 + un rbAmp UI1 + Wi-Fi. Contabilidad: unidireccional. La misma lógica de tramos sirve para las líneas STD: basta con pasar por ella los acumuladores de consumo y de exportación.

C++
#include 
#include 
#include 

#define RB_ADDR 0x50
const char* WIFI_SSID = "ssid";
const char* WIFI_PASS = "password";
const char* MQTT_HOST = "192.168.1.10";

// NTP. Use a regional pool, then fall back to a global pool.
const char* NTP_PRIMARY   = "pool.ntp.org";
const char* NTP_SECONDARY = "time.google.com";

// Local timezone in POSIX TZ format. Example: Central Europe (Berlin / Warsaw).
//   CET = standard offset +1, CEST = daylight offset +2,
//   M3.5.0/2 = last Sunday of March 02:00 → DST starts,
//   M10.5.0/3 = last Sunday of October 03:00 → DST ends.
const char* TZ_INFO = "CET-1CEST,M3.5.0/2,M10.5.0/3";

// Time-of-use schedule: peak hours [PEAK_START_HOUR .. PEAK_END_HOUR), local time.
const int PEAK_START_HOUR = 8;   // inclusive
const int PEAK_END_HOUR   = 22;  // exclusive

WiFiClient   espClient;
PubSubClient mqtt(espClient);

uint32_t t_prev_ms = 0;

/** @brief  Energy totals for the current day, split by tariff. */
struct DayTotals {
  double peak_wh     = 0;   // Wh consumed during peak hours
  double off_peak_wh = 0;   // Wh consumed during off-peak hours
  int    day_of_year = -1;  // tm_yday of the day these totals belong to
};
DayTotals today;

/** @brief  Lifetime totals, never reset by the daily roll-over. */
struct LifetimeTotals {
  double peak_wh     = 0;
  double off_peak_wh = 0;
};
LifetimeTotals lifetime;

/**
 * @brief  Connect to WiFi (blocking with progress dots on Serial).
 */
void wifi_connect() {
  WiFi.mode(WIFI_STA);
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  Serial.print("WiFi");
  while (WiFi.status() != WL_CONNECTED) { delay(500); Serial.print('.'); }
  Serial.printf(" up, IP=%s\n", WiFi.localIP().toString().c_str());
}

/**
 * @brief  Synchronise the system clock with NTP and apply the local timezone.
 * @details Blocks until the first valid time is received (timeout 15 s).
 *          On timeout the function returns anyway; subsequent reads will see
 *          tm_year == (1970-1900) and the caller can detect this.
 */
void ntp_sync() {
  configTime(0, 0, NTP_PRIMARY, NTP_SECONDARY);   // raw UTC first
  setenv("TZ", TZ_INFO, 1);                       // then apply local TZ
  tzset();

  Serial.print("NTP sync");
  time_t now = 0;
  uint32_t t0 = millis();
  while (now < 1700000000 && millis() - t0 < 15000) {  // sanity: ≥ year 2023
    delay(500);
    Serial.print('.');
    time(&now);
  }
  struct tm tm_now;
  localtime_r(&now, &tm_now);
  Serial.printf(" %04d-%02d-%02d %02d:%02d:%02d %s\n",
                tm_now.tm_year + 1900, tm_now.tm_mon + 1, tm_now.tm_mday,
                tm_now.tm_hour, tm_now.tm_min, tm_now.tm_sec, tm_now.tm_zone);
}

/**
 * @brief  Decide whether a given local hour falls inside the peak tariff window.
 * @param  hour  Hour of day, 0..23 (local time).
 * @return true if peak, false if off-peak.
 * @details For schedules that span midnight (e.g. peak is 22..6),
 *          swap the test to `(hour >= PEAK_START_HOUR || hour < PEAK_END_HOUR)`.
 */
bool is_peak_hour(int hour) {
  return (hour >= PEAK_START_HOUR && hour < PEAK_END_HOUR);
}

/**
 * @brief  Format the current local time as ISO 8601 (with offset).
 * @param  out      Destination buffer.
 * @param  out_len  Buffer size.
 */
void format_iso_now(char* out, size_t out_len) {
  time_t now;
  time(&now);
  struct tm tm_now;
  localtime_r(&now, &tm_now);
  strftime(out, out_len, "%Y-%m-%dT%H:%M:%S%z", &tm_now);  // e.g. 2026-05-22T18:30:00+0200
}

/**
 * @brief  Add the snapshot energy of one period to the right tariff bucket,
 *         and roll the daily totals over at midnight.
 * @param  e_wh    Energy accumulated during the period, Wh.
 * @param  tm_now  Local time at the moment of the snapshot (NOT at period start).
 */
void accumulate_energy(double e_wh, const struct tm& tm_now) {
  // Daily roll-over: when the day changes, publish yesterday's totals
  // (if any) and reset.
  if (today.day_of_year != tm_now.tm_yday) {
    if (today.day_of_year >= 0) {
      char payload[192];
      snprintf(payload, sizeof(payload),
        "{\"yday\":%d,\"peak_wh\":%.3f,\"off_peak_wh\":%.3f,\"total_wh\":%.3f}",
        today.day_of_year,
        today.peak_wh, today.off_peak_wh,
        today.peak_wh + today.off_peak_wh);
      mqtt.publish("rbamp/tou/day_close", payload, true);
      Serial.printf("Day closed: %s\n", payload);
    }
    today = {};                                  // reset
    today.day_of_year = tm_now.tm_yday;
  }

  // Add to the right bucket. The choice is made on the snapshot instant —
  // accurate enough at 60 s periods (boundary error < 60 s/day).
  if (is_peak_hour(tm_now.tm_hour)) {
    today.peak_wh    += e_wh;
    lifetime.peak_wh += e_wh;
  } else {
    today.off_peak_wh    += e_wh;
    lifetime.off_peak_wh += e_wh;
  }
}

/**
 * @brief  Publish one tariff-tagged state to MQTT.
 * @param  iso     ISO 8601 timestamp of the measurement.
 * @param  avg_p   Time-averaged power over the just-closed period, W.
 * @param  e_wh    Energy added to the totals in this period, Wh.
 * @param  peak    true if the current hour is a peak hour.
 */
void publish_state(const char* iso, float avg_p, double e_wh, bool peak) {
  char payload[384];
  snprintf(payload, sizeof(payload),
    "{"
      "\"ts\":\"%s\","
      "\"tariff\":\"%s\","
      "\"avg_p\":%.1f,"
      "\"period_wh\":%.4f,"
      "\"today_peak_wh\":%.3f,"
      "\"today_off_peak_wh\":%.3f,"
      "\"life_peak_wh\":%.3f,"
      "\"life_off_peak_wh\":%.3f"
    "}",
    iso, peak ? "peak" : "off_peak",
    avg_p, e_wh,
    today.peak_wh, today.off_peak_wh,
    lifetime.peak_wh, lifetime.off_peak_wh);
  mqtt.publish("rbamp/tou/state", payload, false);
  Serial.printf("%s\n", payload);
}

void setup() {
  Serial.begin(115200);

  // 1) WiFi and NTP — get the wall clock first.
  wifi_connect();
  ntp_sync();

  // 2) MQTT.
  mqtt.setServer(MQTT_HOST, 1883);
  mqtt.setKeepAlive(60);                         // 60 s keepalive (default 15 s)
  mqtt.setBufferSize(512);
  mqtt.connect("rbamp-tou");                     // best-effort; loop() retries

  // 3) rbAmp.
  Wire.begin();
  Wire.setClock(50000);
  delay(300);
  while ((rb_read_u8(RB_ADDR, 0xCE) & 0x01) == 0) delay(50);

  rb_write_u8(RB_ADDR, 0x01, 0x27);              // primer snapshot
  t_prev_ms = millis();

  Serial.printf("TOU started: peak %02d:00..%02d:00 local\n",
                PEAK_START_HOUR, PEAK_END_HOUR);
}

void loop() {
  // Maintain MQTT session: reconnect with bounded back-off (no blocking).
  if (!mqtt.connected()) {
    static uint32_t last_retry = 0;
    if (millis() - last_retry > 5000) {
      last_retry = millis();
      mqtt.connect("rbamp-tou");
    }
  }
  mqtt.loop();

  static uint32_t last_period = 0;
  if (last_period == 0) last_period = millis();  // seed on first iteration
  if (millis() - last_period < 60000) {
    delay(50);                                   // short slice — keeps mqtt.loop responsive
    return;
  }
  last_period = millis();

  // ----- Snapshot + period read -----
  rb_write_u8(RB_ADDR, 0x01, 0x27);
  uint32_t t_now_ms = millis();
  delay(50);

  if ((rb_read_u8(RB_ADDR, 0x07) & 0x01) == 0) {
    Serial.println("WARN: stale snapshot, skipping");
    t_prev_ms = millis();
    return;
  }
  float avg_p = rb_read_float_le(RB_ADDR, 0xDC);
  float dt_s  = (t_now_ms - t_prev_ms) / 1000.0f;
  double e_wh = (double)avg_p * dt_s / 3600.0;
  t_prev_ms = t_now_ms;

  // ----- Tag with current local time, choose tariff bucket -----
  time_t now_s;
  time(&now_s);
  struct tm tm_now;
  localtime_r(&now_s, &tm_now);

  // Guard against a fresh boot with no NTP yet (year << 2023).
  if (tm_now.tm_year + 1900 < 2023) {
    Serial.println("WARN: clock not yet synced, retrying NTP");
    ntp_sync();
    return;
  }

  accumulate_energy(e_wh, tm_now);

  char iso[40];
  format_iso_now(iso, sizeof(iso));
  publish_state(iso, avg_p, e_wh, is_peak_hour(tm_now.tm_hour));
}

Notes:

  • El chip nunca ve el reloj de pared. El maestro adjunta la marca de tiempo en el momento de la instantánea: es el momento correcto, porque es cuando se cerró la ventana de medición.
  • localtime_r() aplica automáticamente la regla POSIX de TZ, así que los cambios de horario de verano se gestionan correctamente sin código adicional.
  • Error de frontera: un periodo de 60 s que cruza la frontera de las 22:00 se atribuye por completo a fuera de punta (la marca de tiempo está en el instante de la instantánea, después de las 22:00). Para periodos de 60 segundos, son como máximo ~30 s de atribución errónea al día: despreciable para la contabilidad tarifaria residencial. Para periodos de 15 minutos, alinee la instantánea con el límite del horario o reparta el periodo entre ambos tramos.
  • Para la medición bidireccional de un STD, ejecute una segunda llamada a accumulate_energy() en el lado de exportación y publique tanto el consumo punta/valle como la exportación punta/valle.
  • El cambio de día publica a medianoche una carga retenida rbamp/tou/day_close; Home Assistant o una fuente de datos de Grafana pueden suscribirse a ella para registrar los totales diarios.

Ejemplo de carga útil de estado MQTT:

JSON
{
  "ts": "2026-05-22T18:30:00+0200",
  "tariff": "peak",
  "avg_p": 850.5,
  "period_wh": 14.175,
  "today_peak_wh": 4253.7,
  "today_off_peak_wh": 1820.4,
  "life_peak_wh": 285431.2,
  "life_off_peak_wh": 178654.9
}

Ejemplo de carga útil de cierre diario (rbamp/tou/day_close):

JSON
{"yday":141,"peak_wh":4253.7,"off_peak_wh":1820.4,"total_wh":6074.1}

Comparación de ejemplos

# Complejidad Pantalla MQTT DRDY Multimódulo Bidireccional Persistencia Caso de uso
1 mínimo Serie — — — — — prueba de humo
2 bajo OLED — — — — RAM medidor en caja
3 bajo Serie — — sí (3) — — monitorización doméstica
4 medio — sí — — — RAM por electrodoméstico en HA
5 medio Serie — sí — sí (en el maestro) RAM vivienda solar en nivel BASIC
6 alta — sí — sí (3) sí RAM balance energético de toda la casa
7 medio Serie + SD — sí — — Tarjeta SD detección de eventos
8 medio — sí (+disco) — — opcional RAM + MQTT Integración con auto-descubrimiento de HA
9 medio — sí — — — Memoria RTC registrador exterior / autónomo
10 medio Serie sí — — opcional RAM + MQTT (cierre diario) Medición TOU punta/fuera de punta con reloj NTP

Buenas prácticas

  • Compruebe siempre DATA_VALID tras el arranque y PERIOD_VALID tras CMD_LATCH_PERIOD.
  • Use delay(50) tras una instantánea, antes de leerla.
  • El reloj maestro es la autoridad para los Wh: no use PERIOD_LATCH_MS del chip.
  • DRDY ayuda a tasas de sondeo altas (≥ 5 Hz); el sondeo ordinario es suficiente a tasas bajas (≤ 1 Hz).
  • Para configuraciones con varios módulos, la instantánea difundida por llamada general ofrece una sincronización precisa (firmware 1.0 o posterior).
  • La persistencia en el maestro es obligatoria para la contabilidad a largo plazo: rbAmp no almacena Wh, solo el avg_P actual.
  • Al sustituir un rbAmp en un sistema en marcha, guarde en el maestro el total_wh acumulado antes del cambio y restáurelo después: el módulo nuevo empieza sus contadores desde cero.

Lo siguiente

Cuando domine estos diez ejemplos, escriba el código de integración para su plataforma. Bibliotecas ya compiladas:

  • Arduino → clase RbAmp (véase la tabla de bibliotecas cliente del README)
  • ESPHome → componente externo (análisis completo en tools/esphome-rbamp/docs/en/)
  • MicroPython → paquete rbamp (consulte la tabla de bibliotecas cliente del README)
  • ESP-IDF → componente rbamp (consulte la tabla de bibliotecas cliente del README)
  • SBC Linux (CPython) → paquete rbamp (consulte la tabla de bibliotecas cliente del README)
  • Tasmota → driver Berry: pendiente (no se incluye biblioteca)

Si su plataforma no está cubierta, los ejemplos de Arduino sirven de referencia: adapte los auxiliares rb_read_* a la API I²C de su plataforma y el resto de la lógica no cambia.